Manual Bosch AdvancedImpactDrive 18 (page 13 of 175) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766774

Zoom out

Zoom in

1/175

English | 13

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Battery Charging

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

– To remove the battery (4), press the release button (3)

and pull the battery back and out of the power tool. Do

not use force to do this.

Changing the tool (see figureA)

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Inserting the application tool

– Pull the locking sleeve (2) forward, guide the application

tool (1) into the tool holder up to the stop and release the

locking sleeve (2) to lock the application tool.

– Use only screwdriver bits with ball catch (8) (DIN 3126-

E6.3). Other screwdriver bits (9) can be inserted using a

universal bit holder with ball catch (10).

Removing the application tool

– Pull the locking sleeve (2) forward and remove the applic-

ation tool.

Operation

Method of Operation

The tool holder (1) (with the application tool) is driven by an

electric motor via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed

connection runs tight and load is therefore put on the motor.

The impact mechanism then converts the power of the mo-

tor to steady rotary impacts. When loosening screws or nuts,

the process is reversed.

Starting Operation

Inserting the Battery

Set the rotational direction switch (5) to the middle position

to avoid unintentionally switching it on. Insert the charged

battery (4) into the handle until you feel it engage and it is

flush with the handle.

Set the rotational direction (see figureB)

The rotational direction switch (5) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (6) is being pressed.

Right rotation: To drive in screws and tighten nuts, press

the rotational direction switch (5) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (5) through to the right

stop.

Switching on/off

To start the power tool, press and hold the on/off switch

(6).

To switch off the power tool, release the on/off switch (6).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (6) to varying extents.

A light pressure on the on/off switch (6) results in a low rota-

tional speed. Increased pressure on the switch causes an in-

crease in speed.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

Practical advice

uOnly apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

The torque depends on the impact duration. The maximum

achieved torque results from the sum of all individual

torques achieved through impact. Maximum torque is

achieved after an impact duration of 6–10 seconds. After

this duration, the tightening torque is increased only minim-

ally.

Bosch Power Tools 1 609 92A 4XB | (17.11.2020)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedImpactDrive 18 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 3,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedImpactDrive 18 Manual

Product: