Manual Bosch AdvancedGrind 18 SystemBox (page 22 of 323) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766843

Zoom out

Zoom in

1/323

22 | English

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Clean the grinding spindle (17) and all the parts to be fitted.

Lock the grinding spindle with the spindle lock button (2)

before clamping and releasing the abrasive tools.

uDo not press the spindle lock button while the grind-

ing spindle is moving. The power tool may become dam-

aged if you do this.

Grinding/Cutting Disc

Pay attention to the dimensions of the abrasive tools. The

diameter of the hole must match that of the mounting flange.

Do not use an adapter or reducer.

When using diamond cutting discs, make sure that the direc-

tion of rotation arrow on the diamond cutting disc corres-

ponds to the direction of rotation of the machine (see direc-

tion of rotation arrow on the housing).

See the graphics page for fitting instructions.

Use the quick-clamping nut (16) to secure the grinding/cut-

ting disc without the need for additional tools.

uThe quick-clamping nut (16) may be used only for

grinding or cutting discs.

uOnly use quick-clamping nuts (16) that are in good

working order and not damaged.

uWhen screwing on, make sure that the printed side of

the quick-clamping nut (16) is not facing the grinding

disc.

uAlways secure a grinding/cutting disc using only the

quick-clamping nut (16) supplied.

Press the spindle lock but-

ton (2) to lock the grinding

spindle. To tighten the

quick-clamping nut (16),

fold up the bar and turn the

quick-clamping nut firmly

clockwise. Then fold down

the bar to secure the quick-

clamping nut. It is not suf-

ficient to tighten the disc

along the edge.

Quick-clamping nuts (16)

that are properly secured

and not damaged can be re-

moved by hand. To do this,

fold up the bar and turn the

quick-clamping nut firmly

anticlockwise. If the quick-

clamping nut is stuck, do

not attempt to loosen it with

a tool – always use a two-

pin spanner.

After fitting the hub flange

and the grinding/cutting

disc, the free thread length

of the grinding spindle must

be at least 4mm.

Ensure that the abrasive

tool is firmly seated, so that

it does not twist away from

the spindle in the runout of the power tool.

A plastic part (O-ring) is fitted around the cent-

ring collar in the hub flange (11). If the O-ring

is missing or damaged, the hub flange (11)

must be replaced before operation can re-

sume.

uAfter fitting the abrasive tool, check that the abrasive

tool is fitted correctly and can turn freely before

switching on the power tool. Make sure that the abras-

ive tool does not brush against the protective guard or

other parts.

Flap disc

uAlways fit the hand guard (18) when working with the

flap disc.

Rubber Sanding Pad

uAlways fit the hand guard (18) when working with the

rubber sanding pad (19).

See the graphics page for fitting instructions.

Slide the rubber sanding pad (19) onto the grinding spindle

(17).

Press the sanding sheet (20) firmly onto the underside of

the rubber sanding pad (19).

Screw on the round nut (21) and tighten with a two-pin

spanner.

Cup brush/disc brush

uAlways fit the hand guard (18) when working with the

cup brush or disc brush.

See the graphics page for fitting instructions.

The cup brush/disc brush must be screwed onto the grinding

spindle until it rests firmly against the grinding spindle flange

at the end of the grinding spindle thread. Tighten the cup

brush/disc brush with an open-ended spanner.

1 609 92A 6D6 | (25.06.2021) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedGrind 18 SystemBox in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 11,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedGrind 18 SystemBox Manual

Product: