606589
37
Zoom out
Zoom in
Previous page
1/456
Next page
English | 37
Bosch Power Tools F 016 L81 517 | (27.10.15)
EN 301 489-7 V1.3.1 (EMC and ERM for GSM and DCS),
EN 301 511 V9.0.2 (GSM 900 and GSM 1800 Bands Essen-
tial Requirements), EN 55014-1:2006+A2:2011 (EMC
Emissions),EN 55014-2:1997+A2:2008 (EMC Immunity).
Guaranteed sound power level 75 dB(A).
Conformity assessment procedure according to Annex VI.
Equipment category: 32
Notified body for 2000/14/EC:
SRL, Sudbury, England, Nr. 1088
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2,
Stowmarket, Suffolk IP14 1EY, England
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 27.10.2015
Explanation of Installation Guide
(seepages3–14)
Lawn Preparation
Remove stones, loose pieces of wood, wire, live mains cables
and other foreign objects from the cutting area.
Make sure that the cutting area is even and has no ditches,
grooves and steep slopes above 20° that are clear obstruc-
tions for the machine.
Cut the main area of the lawn with a conventional mower to a
max. height of 40 mm and the perimeter wire area to a max.
height of 20 mm.
Installation
For a video guide on how to install the Indego please visit
www.bosch-indego.com or use the following QR-Code.
Select a position for the docking station, horizontally levelled
and out of direct sunlight.
Note: The docking station must be positioned on the wire at
an outer edge of the cutting area. It cannot be positioned by
the side of a shed or workshop that appears as an island with-
in the cutting area.
Make sure that the docking station is placed beside the cut-
ting area with a straight 1.5 m track in front of the docking sta-
tion and a straight 1 m track behind. Whilst stood in the grass
area to be cut it is important that the docking station charging
pins point to the left. (see figure 2)
Note: If the docking station is positioned with the charging
pins pointing either into the grass area or pointing to the right
the Indego will not run correctly.
Pull the wire end through the front hole of the base plate and
straight through the wire duct and the rear hole. Fix the wire
with a peg inline with the hole. Cut off insulation carefully and
connect the wire to the right hand (red) terminal. (see
figures 5– 6)
Fix the docking station with 4 supplied fixing pins to the
ground. (see figure 7)
Lay out the perimeter wire anti-clockwise and flush to the
ground. Observe the minimum distances from lawn edges,
steps, walls, ponds, etc. Use the spacing guide. (see figure 8)
Note: The cable should be positioned so that the Indego will
not be more than 16 m away at anytime.
If the working area borders against a flat path or surface that
is level with the lawn the Indego will be able to run over it. In
such cases the perimeter wire should be positioned right up
to the edge of the lawn.
Note: Perimeter wire can be buried up
to a maximum depth of 5 cm. It is recommended to mark out
permanent objects within the garden. This will prevent the In-
dego colliding with the object and reduce wear on the shell.
Objects on the lawn below 6 cm height e.g. trees, ponds, flow-
er beds etc. must be delimited in a clockwise direction. The
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Action Figure Page
Delivery scope/unpacking product
1 4
Position the docking station
2–4 4–6
Thread wire through base plate
5 6
Connect first end of perimeter wire
6 6
Fix docking station to the ground
7 6
Lay out perimeter wire
8 7
Extend perimeter wire
9 8
Lay out additional area with perimeter
wire 10 8
Connect second end of perimeter wire
11 9
Clip on protective cover of docking
station
12 9
Install power supply
13 10
Docking station indicates power on
14 10
Plug in isolator key
15 10
Charge battery by putting the machine
into docking station
16 11
Welcome screen = Refer to manual
17 11
Lift up and carry the machine
18 12
Set height of cut
19 12
Logicut Intelligent Cutting
20 13
Cleaning
A 14
Maintenance
B 14
OBJ_BUCH-1573-008.book Page 37 Tuesday, October 27, 2015 10:35 AM
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch 3600 HA2 - Indego 1000 Connect at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch 3600 HA2 - Indego 1000 Connect in the language / languages: All languages as an attachment in your email.

The manual is 89,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch 3600 HA2 - Indego 1000 Connect

Bosch 3600 HA2 - Indego 1000 Connect Installation Guide - Dutch - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info