Manual Bort BSS-3500-St (page 17 of 48) (English, German)

555095

Zoom out

Zoom in

1/48

MAINTENANCE

Empty the water from the water tank and dry body after

using the unit. Please cleaner the ﬁ lter cotton in the

dustbin, cover of dustbin and under of machine, after

you are using the machine.

TROUBLE SHOOTING

If the unit does not turn on, check to see that

it is connected properly to the power source If

steam stops coming out, check to see that

there is enough water in the water tank If the vacuum

function does not work properly, check to see that the

dustbin has been cleaned and is empty and is attached

properly back into the unit.

If there is and damage to the power cord, plug or not

attempt to ﬁ x the unit by yourself. Consult a qualiﬁ ed

electrician to get problem ﬁ xed before using the unit

again.

CAUTION: To reduce the risk of electric

shock, do not remove the hose while machine

is on.

This hose contains electrical connections:

- Do not immerse in water for cleaning;

- The hose should be checked and must not be used

if damaged.

WARNING: To prevent ﬁ re or electric shock, do not

expose this equipment to rain or moisture.

USING TOUR APPLIANCE

HOW TO CLEAN WITH STEAM-STEAM-USEFUL

TIPS

To make the most of your steam cleaner the following

tips will be helpful in making cleaning tasks easier,

safer and more productive.

There are on set rules on how to clean with steam,

however the key to using your steam cleaner

successfully is to use right tool and set your body in

the best possible position to comfortably do each job.

There are many areas where steam can be used to

clean. Do not be afraid of trying something new or

attempting to clean something that you have not tried

to clean before.

If you are unsure if seam may cause damage to a

particular surface, always test a small surface ﬁ rst

before attempting to clean the whole area.

4. After ﬁ lling the water into the water tank, push

down and screw the steam pressure release device in

clockwise direction until the cap is screwed on tight.

After the cap appears to be on tight, double check it is

on properly by pressing the cap down and turn until the

cap is tight and cannot turn tighter.

Once the water starts heating, if you hear steam

pressurizing out of the cap , then you need turn off the

power, and take a towel, place it over the cap, press

down the cap and tighten until it won’t move anymore.

When reﬁ lling water, the unit must be disconnected

from power supply, and the steam pressure cap shall

not be opened until the water tank cools down.

Note: Even if don’t recommend it, but if you require

to reﬁ ll the tank immediately, use a towel to carefully

unscrew the cap as the cap will still be very hot.

If you do reﬁ ll the tank immediately. Be very careful

as the boiling water may splash out of the boiler and

cause potential burns to your skin.

5. Please check the water level in the dustbin, when

you want using the vacuum cleaner, and then close the

dustbin cover.

When the dustbin inhaled plenty of water or dust,

protect the device will start, at this time, you will feel no

suction power, we only need to clean up dustbin, and

then to ﬁ ll (500 ml – 750 ml) minimum 500 ml water

(2 Measuring cups), close the dustbin cover, and you

can to use again.

6. Plug into a power outlet (220–240 v) and switch on

the steam or vacuum button, to use the function as

required by you.

7. To use the steam function, press the steam button to

on position and then wait for the “steam ready” light to

go on. About 8 minutes. The steam is now ready to use.

After joining the steaming (cleaning) head to the plug

of the tube, switch on the ”LOCK” button (turning it on

right) to ensure the head not to be separated from the

tube during the using.

Press the trigger on the gun and use the steam volume

adjustment knob to operate steam function as required.

Use the steam lock if continuous steam is required.

When ﬁ rst using the steam, hold the steam outlet over

a sink or into a bucket as it may produce excessive

water for the for 10–20 seconds or until the steam

becomes dry. If your job requires more moisture then it

will be ok to use immediately after heating up.

8. After using the steam function for a while, the

steam pressure may weaken. If you require the steam

pressure to build up again, let go off the steam until the

ready light goes off.

9. To use the vacuum function, press the vacuum

button to on position and vacuum with the accessory

required.

10. To empty the vacuum waste tank, ﬁ rst switch off

the steam and vacuum buttons and unplug the unit.

Open the cover and pull out the dustbin b by using the

handle. Empty and clean the dustbin, push back into

place and close the cover.

11. Before attaching any accessory to the unit or the

steam gun, make sure the steam is off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bort BSS-3500-St in the language / languages: English, German as an attachment in your email.

The manual is 3,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bort BSS-3500-St Manual

Product: