Manual Bort BSS-1800N-ECO (page 8 of 24) (English)

555077

Zoom out

Zoom in

1/24

STORAGE OF THE CLEANER

1. Upon the completion of the operation of the cleaner,

turn off its power supply, and pull the power plug out of

the power socket, then step on the cord reeling button

to reel in the power cord fully. Hang the ﬂ oor brush onto

the ﬂ oor brush hook, as is shown in Figure (7).

1. Place the cleaner in the dry indoor environment.

CLEANING OF THE DUST BARREL

Remove the rubbish in the dust barrel frequently to

avoid the failure of the cleaner.

1. Clean the dust barrel only after the power plug of the

cleaner has been pulled out;

2. Put the dust barrel over the rubbish bin (bag), press

down the releasing button of the dust barrel, the bottom

cover of the dust barrel will automatically fall down, and

clear and empty the dust barrel, as is shown in Figure

(8).

Cleaning of front ﬁ lter for motor:

Warning: please make sure the power supply of

the cleaner has been cut off before carrying out the

following steps:

1. Pull out the power cord plug of the cleaner from the

power socket.

2. Press down the handle of the dust barrel to remove

the dust barrel, and remove the cover of the front ﬁ lter

for motor, and then use the brush to clean the ﬁ lter

(sponge and ﬁ lter gauze with composite coating) or

place it under the cock to clean, as is shown in Figure

(9/10).

Caution:

It is normal that the white central ﬁ lter in the dust barrel

may change color, which cannot affect its ﬁ ltration

performance. If the hose and the central ﬁ lter are

difﬁ cult to clean, we recommend that you use water to

ﬂ ush them; however, please be sure to place them in

the dry air for at least 24 hours after they are ﬂ ushed

by water.

Key Points:

Please note: when the dust collecting barrel or the ﬁ lter

cover is not installed in place, the operation status will

be invalid, and the cleaner will have no dust absorption

capacity. At this time, you need to check carefully

whether the dust collecting barrel and the ﬁ lter cover

have been installed in place.

Caution: please keep the suction passage unobstructed,

otherwise the motor may become overheating or even

be damaged.

REPLACEMENT OF REAR FILTER

FOR MOTOR

The rear ﬁ lter for motor is installed behind the air outlet

grid, which can be washed due to the materials used.

When the surface is jammed seriously by dust, the ﬁ lter

should be replaced by a new one or washed by water

to maintain enough suction force. (Figure 11/12)

It is usually necessary to clean and replace the ﬁ lters

for motor only after they have been used for 6 months

to 12 months. Please remember to conﬁ rm that all

ﬁ lters have been correctly installed into the machine

before turning on the cleaner to use.

handle is pressed down to the bottom, the dust barrel

can be lifted to remove.

ASSEMBLY OF METAL EXTENSION PIPE

AND FLOOR BRUSH

Insert the front end of the hose handle into the metal

extension pipe according to Figure (5); then insert

the other end of the metal extension pipe into the

rounded inlet of the ﬂ oor brush, and adjust to the

proper direction. At this time, the assembly of the whole

machine is completed.

OPERATION INSTRUCTIONS

HOW TO START

1. First of all, pull out the power cord from the cord reel

to the needed length; insert the power cord plug into

the power socket, and press down the power switch

button with ﬁ nger or step on it with foot; then you can

control the start and stop of the cleaner.

2. The yellow mark on the power cord indicates its

desired length. Never pull out the power cord to the

length exceeding the red mark.

CONTROL OF SUCTION FORCE

When the suction inlet is jammed by some cloth due

to the over-large suction force, you can adjust the air

escape pushbutton on the hose handle to control the

suction force at the suction inlet, as is shown in Figure

(6).

PROTECTIVE DEVICES OF MOTOR

1. There is a temperature controller designed in the

body of cleaner motor, which can automatically cut

off the power supply of motor to prevent overheating.

When the air-inlet or air-outlet pipe is overloaded or

blocked, the temperature of motor rises, then the

temperature controller cuts off the power supply of

motor automatically to make the motor cool, preventing

the cleaner from being damaged.

2. If the temperature controller is cut off, stop the

cleaner immediately and pull out the power plug to

make the cleaner cool, and check and remove the

hair roll or other roll-like rubbish blocking the air inlet

(including the hose and the spile), and replace the ﬁ lter

HEPA or ﬁ lter gauze when necessary.

3. After cooling the motor for 30mins, plug in the power

plug and check whether the temperature controller has

been reset. If the power supply of the cleaner hasn’t

been cut off, the temperature controller of the motor

won’t be reset even when the motor has become cool.

MAINTENANCE OF THE CLEANER

All the day-to-day maintenance and repair jobs should

be done after the power plug has been pulled out.

2. Frequently remove the rubbish from the dust barrel,

so as to avoid the failure of the cleaner.

3. Never wipe the surface of the cleaner with gasoline

or oily liquid. Wipe it with water or neutral detergent.

Caution: be sure to wring out the wiping cloth dry for

wiping, it is prohibited for water to inﬁ ltrate into electrical

elements of the cleaner.

3. When the cleaner is placed idle not in use, it should

not be put directly in the sun or in a damp place.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bort BSS-1800N-ECO in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bort BSS-1800N-ECO Manual

Product: