555169
9
Zoom out
Zoom in
Previous page
1/108
Next page
9
GB
E
Never start or stop the spray gun while it is aimed at
the surface to be sprayed. Evenly control the speed of
movement of the spray gun. A fast speed of movement
over the surface will give a thin coat and aslowspeed
will givea heavy coat. Apply one coat at a time. If a fur-
ther coat is required, make sureyou observe the manu-
facturers drying time recommendations before apply-
ing a second coat. When spraying small areas, keep
the output control on a low setting. This will avoid using
too much paint and prevent overspray. Where possible,
avoid stopping and starting when spraying an object.
This can lead to too much, or not enough paint being
applied. Do not tip the spray gun to more than 45°
CLEANING AND MAINTENANCE
Always remember to disconnect from the
mains supply before cleaning the spray gun
or paint container.
It is essential that the spray gun is cleaned thoroughly
after every use. Failure to clean it will almost certainly
result in blockages and it may not operate when you
next come to use it! The guarantee does not cover
cleaning a sprayer that has not been properly cleaned
by the user.
The following action must be taken after every
use.
1. Empty any remaining material from the container.
2. Clean the container thoroughly with the thinner
thatwas used.
3. Pour some thinner into the container and spray
through the spray gun until only clean thinner is
coming out of the nozzle.
4.Thoroughly clean the paint pick uppipeand lter with
thinner.
5.Clean the basket and nozzle and remove any other
debris or paint that remains.
Air lter cleaning
F
Unscrew the air lter cover (A).
• Remove lter element and wash well in solvent.
• Replace the lter element and air lter cover (A).
Be sure the lter cover seals properly all around.
TROUBLE SHOOTING
Motor hums but does not spray or irregular spray-
ing.
1. Worn swirl head
Replace swirl head.
2. Pick up pipe not into the right position
Re-adjust pick up pipe.
3. Blocked pick up pipe
Clean with thinner.
4. Blocked nozzle
Clean nozzle.
5. Blocked lter
Clean with thinner.
6. Control knob needs adjustment
Adjust.
Atomization is not good.
1. Volume adjustment is not correct.
Adjust
2. Paint too thick
Check viscosity of the paint
Over painting.
1. Spray gun not clean, or not lubricated, resulting in
piston being stuck in cylinder
Disassemble spray gun and dean with thinner.
2. Too much paint
Adjust the volume clockwise to reduce spraying.
Two t/i/n coats are better then one thick coat.
3. Viscosity too low
Check viscosity
Motor louderthan normal.
1. Spray gun not clean, or not lubricated, resulting in
piston being stuck in cylinder
Disassemble spray gun and clean with thinner.
No spray, no sound.
1. No electricity
Check power supply.
Operating sound not right.
1. Poor output adjustment
Re-adjust
2. Not enough paint in the container resulting in air
being sucked in.
Re ll with paint
3. Not diluting properly or not passing pick up pipe
completely.
Check pick up pipe and viscosity level.
«Orange Skin» excessive fogging.
1. Incorrectsolventis used
Use correct solvent
2. Spray gun too far from the surface.
Hold spray gun closer to Vie object
3. Paint too thick
Thin the paint
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bort BFP-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bort BFP-500 in the language / languages: All languages as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info