555166
8
Zoom out
Zoom in
Previous page
1/108
Next page
8
GB
- SWITCH OFF WHEN NOT SPRAYING - Avoid run-
ning the unit with the ow rate knob fully closed for
any length of time.
We accept no responsibility for damage caused by
the use of unsuitable substances, or paints that hare
not been thinned correctly, and any health hazards
that arise from lack of adequate ventilation
IMMEDIATELY SWITCH OFF THE SPRAY
GUNWHEN:
Interruption in the mains plug, mains lead or mains
lead damage.
• Defectswitch.
Smoke or stench of scorched isolation.
OPERATION INSTRUCTIONS
PREPARATION B
Do not use textured wall paints or coatings as
this wHIblock the nozzle.
To obtain the best results, it is important that you pre-
pare the surface to be sprayed and thin the paint to
the correct viscosity, before you operate your spray
gun. Always ensure that the surfaces to be sprayed
are free from dust, dirt and grease. Make sure that you
have masked the areas that should not be sprayed,
using a good quality masking tape. The paint or uid
to be sprayed should be thoroughly mixed and free
from lumps or other particles. Many substances can
be sprayed with your spray gun, but always check the
manufacturers recommendations before purchasingy-
our paint.
THINNING
Always rememberto disconnect from the
mains sup-ply before lling the paint contain-
er with sprayable material.
Most paints are supplied ready for brush application
and will need to be thinned before they are suitable to
be sprayed. Follow the manufacturers advice on thin-
ning the paint when used with a spray gun. The viscos-
ity cup will help you to determine the correct viscosity of
paint to be used. To determine the correct viscosity, ll
the cup to the brim with the paint. Measure the amount
of time it takes for the cup to empty back into the can.
The table below shows recommended times for differ-
ent types of material.
Plastic & latex paint 24 - 28 seconds
Water based paint 20-25 seconds
Primers 24-28 seconds
Varnishes 20-25 seconds
Oil based paints 18-22seconds
Enamel paints 18-22seconds
Aluminium paints 22-25 seconds
Carundersealing 25-35 seconds
Wood sealers 28-35 seconds
Wood preservatives Nothinningrequired
Wood stains Nothinningrequired
If the paint takes longer than the recommended time to
empty, then further thinning is required. Mix in a small
quantity of the appropriate thinner and use the viscos-
ity test until the correct thickness is achieved. Some
sprayable materials contain particles and lumps. These
materials should be strained before lling the paint con-
tainer.
SPRAYING C
Fill the paint container with the correctly thinned and
strained paint. Connect the spray gun to the mains
supply. Aim the spray gun at a piece of scrap material
and operate the trigger switch until paint is spraying.
Adjust the output control
until the required volume
of paint is spraying.
SPRAYING TECHNIQUES D
To obtain the best results, keep your spray gun level
and parallel to the surface at all times.
Keep the nozzle 25 - 30 cm from the surface and spray
evenly from side to side or up and down. Do not spray
at an angle as this will lead to paint runs on the surface.
Use smooth and even strokes. When spraying large
areas, use a criss-cross pattern as shown.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bort BFP-350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bort BFP-350 in the language / languages: All languages as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info