555160

Bort BFP-18A Manual

8
Zoom out
Zoom in
Previous page
1/20
Next page
8
Plastic & latex paint 24 - 28 seconds
Water based paint 20-25 seconds
Primers 24-28 seconds
Varnishes 20-25 seconds
Oil based paints 18-22seconds
Enamel paints 18-22seconds
Aluminium paints 22-25 seconds
Carundersealing 25-35 seconds
Wood sealers 28-35 seconds
Wood preservatives Nothinningrequired
Wood stains Nothinningrequired
If the paint takes longer than the recommended time to
empty, then further thinning is required. Mix in a small
quantity of the appropriate thinner and use the viscos-
ity test until the correct thickness is achieved. Some
sprayable materials contain particles and lumps. These
materials should be strained before fi lling the paint con-
tainer.
SPRAYING C
Fill the paint container with the correctly thinned and
strained paint. Connect the spray gun to the mains
supply. Aim the spray gun at a piece of scrap material
and operate the trigger switch until paint is spraying.
Adjust the output control
until the required
volume of paint is spraying. Turn the output control
in a clockwise direction (B) to reduce the fl ow and
anti-clockwise (A) to increase the fl ow. Adjustment of
the output control will affect the spray pattern. A poor
spray pattern will concentrate the paint in the centre
of the spray and give a blotchy fi nish. A good spray
pattern will give even distribution of paint throughout
the pattern.
SPRAYING TECHNIQUES D
To obtain the best results, keep your spray gun level
and parallel to the surface at all times.
Keep the nozzle 25 - 30 cm from the surface and spray
evenly from side to side or up and down. Do not spray
at an angle as this will lead to paint runs on the surface.
Use smooth and even strokes. When spraying large
areas, use a criss-cross pattern as shown.
E
Never start or stop the spray gun while it is aimed at
the surface to be sprayed. Evenly control the speed of
movement of the spray gun. A fast speed of movement
over the surface will give a thin coat and aslowspeed
will givea heavy coat. Apply one coat at a time. If a fur-
ther coat is required, make sureyou observe the manu-
facturers drying time recommendations before apply-
ing a second coat. When spraying small areas, keep
the output control on a low setting. This will avoid using
too much paint and prevent overspray. Where possible,
avoid stopping and starting when spraying an object.
This can lead to too much, or not enough paint being
applied. Do not tip the spray gun to more than 45°
CLEANING AND MAINTENANCE F
It is essential that the spray gun is cleaned thoroughly
after every use. Failure to clean it will almost certainly
result in blockages and it may not operate when you
next come to use it! The guarantee does not cover
cleaning a sprayer that has not been properly cleaned
by the user.
The following action must be taken after every
use.
1. Empty any remaining material from the container.
2. Clean the container thoroughly with the thinner
thatwas used.
3. Pour some thinner into the container and spray
through the spray gun until only clean thinner is
coming out of the nozzle.
4.Thoroughly clean the paint pick uppipeand fi lter with
thinner.
5.Clean the basket and nozzle and remove any other
debris or paint that remains.
6. Turn the spray gun upside down and apply a few
drops of light oil to the two apertures (F). This will
lubricate the piston and cylinder.
If your spray gun should require extra internal
cleaning, it may be necessary to disassemble it. If
so the following action should be taken.
1. Remove paint container, pick up pipe and fi lter.
2. Release the nozzle (H), valve (j), piston (K) and
spring (L).
3. Clean the cylinder (M) and all parts thoroughly with
solvent.
4. Apply a few drops of light lubricating oil to the pis-
ton, springand cylinder.
5. Reassemble the spray gun.
TROUBLE SHOOTING
Motor hums but does not spray or irregular spray-
ing.
1. Worn swirl head
Replace swirl head.
2. Pick up pipe not into the right position
Re-adjust pick up pipe.
3. Blocked pick up pipe
Clean with thinner.
4. Blocked nozzle
Clean nozzle.
5. Blocked fi lter
Clean with thinner.
6. Control knob needs adjustment
Adjust.
Atomization is not good.
1. Volume adjustment is not correct.
Adjust
2. Paint too thick
Check viscosity of the paint
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bort BFP-18A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bort BFP-18A in the language / languages: English, German, French as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info