Manual Boretti Valloria F102 (page 13 of 24) (English, German, Dutch, French, Italian, Spanish)

534037

Zoom out

Zoom in

1/24

Consult the designs in the front pages referenced in the text

by alphabet letters. Closely follow the instructions set out

in this manual. All responsibility,for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

Installation

The cooker hood must be placed at a minimum distance of 65

cm from the cooking plane for electric cookers and 75cm for

gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater

distance, this has to be taken into account.

Do not tile, grout or silicone this appliance to the wall. Surface

mounting only. Do not fix chimney flue to furniture or fly over

shelves unless the chimney flue can be easily removed, in

case maintenance is ever required.

Use

The cooker hood is provided with an upper air exit B for

discharging fumes externally for models including chimney

flue C ( Suction Version A- exhaust pipe not supplied).

If cooking fumes and vapours cannot be externally discharged,

the cooker hood can be used in the recirculating version

F: the installation of 1 active charcoal filter F allows the

recirculation of fumes and vapours through the upper grid G.

Electrical connection

The electrical tension must correspond to the tension noted on

the label placed inside the cooker hood. Connect the electrical

plug, where provided, to the an easily accessible outlet in

conformity with local standards in force.

Where an electrical plug is not provided (for direct connection

to electrical network) place a standards approved bipolar

switch with an aperture distance of not less than 3mm

(accessible) from he contacts.

Operation

A C B D E F

INSTRUCTION ON MOUNTING AND USE

Maintenance

Prior to any maintenance operation ensure that the cooker hood

is disconnected from the electrical outlet.

Cleaning:

The cooker hood should be cleaned regularly internally and

externally.For cleaning use a cloth moistened with denatured

alcohol or neutral liquid detergents. Avoid abrasive detergents.

Warning: Failure to carry out the basic standards of the cleaning

of the cooker hood and replacement of the filters may cause fire

risks. Therefore we recommend observing these instructions.

Anti-grease Filter – must be cleaned once a month, with non

abrasive detergents, by hand or in dishwasher on low temperature

and short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

Charcoal Filter - (only for filter version):

The active charcoal filters F are not washable nor regenerative.

It should be changed every 6 months in normal use.

The active charcoal filters capture unpleasant cooking odours.

Replacing lightbulbs

Warning! Prior to touching the light bulbs ensure they are cooled

down.

With the hood switched off, pressing any key will activate

the control panel in stand-by mode. The symbols are

backlit by a white light, allowing you view and select the

desired function.

Pressing one of the keys again will start the corresponding

function, and its symbol will light up. After all functions

have been switched off, the control panel will remain in

stand-by mode for around 30 seconds and then switch off

automatically.

A: Light ON/OFF key: press this touch sensor to switch

on or off the lights of the hood.

C: Motor ON/OFF key (4 speed): press this touch sensor

to switch on the hood extractor fan at the same speed as it

was when last switched off. Use the „D“ and „B“ keys to

vary the speed (power) of extraction.

B: Decrease extraction speed (power) key: press this

touch sensor to reduce the extraction speed of the hood.

D: Increase extraction speed (power) key: press this

touch sensor to increase the extraction speed of the hood.

E: Timer key: when this touch sensor is pressed,

independently of the extraction speed selected, the timer

function will be activated. Press once to set the timer for 5

minutes, press a second time for 10 minutes and a third

time for 20 minutes. During this phase, the „E“ symbol will

flash.

To reset the timer, press the motor key, „C“

F: Reset filters key: press this touch sensor to reset the

signal that warns that the metal grease filter (1) is saturated

and the charcoal filter (2) should be replaced.

(1) After 40 hours of using the hood, the „F“

symbol will flash to indicate the necessity of

cleaning the metal grease filters.

(2) After 120 hours of using the hood, the „F“

symbol will light up to indicate the necessity of

replacing the activated charcoal filters.

Sensor function: pressing the „B“ and „D“ keys at the

same time will activate the sensor. In this mode the

extraction speed sets itself automatically and the „B+D“

key flashes intermittently. To return to manual operation,

press either the „B“ or the „D“ key.

LED LIGHT

If the lighting group LED does not work, please contact the

technical service center in order to replace the whole group.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boretti Valloria F102 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boretti Valloria F102 Manual

Product: