Manual Boretti SHP 800 (page 17 of 22) (English, German, Dutch, French)

471884

Zoom out

Zoom in

1/22

Maintenance

Always disconnect the extractor before doing

any maintenance.

Cleaning

The extractor must be cleaned regularly, both

inside and outside. Use a cloth with a neutral

detergent for cleaning. Do not use abrasives!

Note: Not observing the cleaning standards for

the extractor and for replacing and cleaning

the ﬁlters may create a ﬁre hazard. You are

therefore requested to follow the instructions.

Grease ﬁlter

The grease ﬁlter must be cleaned once a

month with mild detergents, by hand or in the

dishwasher at a low washing temperature and

with a short washing cycle.

Carbon ﬁlter (ﬁlter version only)

The carbon ﬁlter may not be washed or reused.

The carbon ﬁlter must be replaced at least

once every 4 months.

Lamp replacement

If the BORETTI LUMINA LED illumination is no

longer working, please call Boretti’s technical

service.

Caution

Never a use the extractor when the grease ﬁl-

ters are not ﬁtted correctly! The extracted air

may not be discharged into a duct that is also

used for extracting smoke from devices which

do not run on electricity.

Always ensure that the room is well ventilated

when the extractor and any other appliances

are used. Cooking on open ﬂames under the

extraction hood is strictly forbidden. Open

ﬂames will damage the ﬁlters, electronics, mo-

tor and illumination and can start a ﬁre. When

frying, watch out constantly that hot fat does

not catch ﬁre.

Strictly observe the technical and safety regu-

lations for the extraction of smoke as laid down

by the relevant local authorities.

time will set the timer at 20 minutes and but-

ton E will ﬂash three times repeatedly.

To switch off the delay timer, press button E

once again.

Filter indication

Button F will ﬂash to indicate when your grease

ﬁlters need cleaning (after 40 hours’ opera-

tion) and when the carbon ﬁlters need to be

replaced (after120 hours’ operation) if you are

operating in recirculation mode.

You can easily reset the ﬁlter indication by

pressing button F.

Hint

Switching on the extractor creates a current

of air. However, it can take a moment before

this current takes effect, which may create the

impression that the extractor is not working

properly. It is therefore advisable to set the

extractor at low speed a few minutes before

you start cooking, so that the air current can

already be effective when you start cooking;

this will also allow you to keep using your ex-

tractor at the lowest speeds. In this way your

extractor makes the least noise, uses the least

energy and gives the best results.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boretti SHP 800 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boretti SHP 800 Manual

Product: