121734

Boretti PRO 100 IX Manual

11
Zoom out
Zoom in
Previous page
1/48
Next page
9
GB
the metal grease filters. (See chapter on ‘Maintenance’).
To reset the 200-hour timer the motor and lights must be switched ‘OFF’.
Push the LED button ‘+’ for 10 seconds.
One flash of the LED lights F and C = function is switched ‘OFF’.
Two flashes of the LED lights F and C = function is switched ‘ON’.
To reset the 100 hours timer back to zero requires the motor and lights must be switched ‘OFF’; then and proceed as follows:
Press the LED button ‘+’ for 3 to 4 seconds and the LED lights F and C will flash to confirm the programme has been reset to
zero.
Instructions for replacing the active charcoal filter are given in the chapter on ‘Recycling’.
Setup Process
Modification: How to adjust the internal microprocessor data to suit the type of motor fitted to this appliance and the
supply frequency of 50 or 60 Hz..
1 - Disconnect the cooker hood from the mains supply.
2 - Push the button 0/1 MOTOR.
3 - Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds.
4 - Slacken the button 0/1 MOTOR (the Leds flash for about 3 seconds : capacity’s confirmation SETUP
PROCESS).
5 - During the flashing time select the motor type used while pushing one of the 5 buttons according to the following
board:
BUTTON 0/1 Light : Motor 8/28 & 8/50 220-240 V AC / 50 Hz.
BUTTON 0/1 Motor : Motor 8/28 & 8/50 220-240 V AC / 60 Hz.
BUTTON Speed ( - ) : Motor PRO 220-240 V AC / 50 Hz.
BUTTON Speed (+ ) : Motor PRO 220-240 V AC / 60 Hz.
BUTTON Intensive speed : Motor K40 & K50 220-240 V AC / 50 Hz.
REMOTE CONTROL HANDSET
Caution, the remote control must be fitted with standard LR03-AAA size 1.5V zinc-carbon alkaline batteries as illustrated Fig. 9.
These batteries should give a long life and constant discharge throughout their life.
These batteries must be disposed of properly and could explode if damaged or exposed to heat. Do not dispose of
on fire.
5 USEFUL HINTS
• To obtain the best performance it is advisable to switch ‘ON’ the cooker hood a few minutes (in the boost setting) before
you start cooking and you should leave it running for approximately 15 minutes after finishing.
• IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD
• Do not leave frying pans unattended during use as over-heated fat and oil might catch fire.
• Do not leave naked flames under this cooker hood.
• Switch ‘OFF’ the electric and gas before removing pots and pans.
• Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate and cooker hood
simultaneously.
6 MAINTENANCE
Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply.
The cooker hood must be kept clean; a build up of fat or grease can be a fire hazard.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Boretti PRO 100 IX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Boretti PRO 100 IX in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info