Manual Boretti PICCOLINO (page 16 of 18) (English, Dutch, French)

533800

Zoom out

Zoom in

1/18

EENN

3130

must be used on a level, stable, non-ﬂammable

surface. The appliance should be protected

from direct draughts and shall be positioned

or protected against direct penetration by any

trickling water (e.g. rain). I fused on a wooden

table the table must be protected with a non-

ﬂammable covering to avoid any discolouring of

the wood.

Parts sealed by the manufacturer or his agent

must not be altered by the user. No modiﬁca-

tions should be made to any part of this barbe-

cue and repairs and maintenance should only

be carried out by a Boretti service engineer.

Connection to Appliance

Connect the gas tap to the appliance by fol-

lowing instruction 1 in the lighting instructions.

Before connection, ensure that there is no de-

bris caught in the head of the gas cylinder, reg-

ulator, burner and burner ports. Spiders and

in sects can nest within and clog the burner/

venturi tube at the oriﬁce. A clogged burner

can lead to a ﬁre beneath the appliance.

Clean burner holes with a heavy-duty pipe

cleaner. Fit the hose to the appliance using a

crimp clip or jubilee clip. If the hose is replaced

it must be secured to the appliance and regula-

tor connections with hose clips.

Disconnect the regulator from the cylinder

(according to the directions supplied with the

regulator) when the barbecue is not in use.

The Barbecue must be used in a well ventilated

area. Do not obstruct the ﬂow of combustion

air to the burner when the barbecue is in use.

ONLY USE THIS BARBECUE OUTDOORS

BEFORE USE CHECK FOR LEAKS

Never check for leaks with a naked ﬂame,

always use a soapy water solution.

To check for leaks

Make 2-3 ﬂuid ounces of leak detecting solu-

tion by mixing one part washing up liquid with

3 parts water.

Ensure the control valve is “OFF”

Connect the regulator to the cylinder and ON/

OFF valve to the burner, ensure the connec-

tions are secure then turn ON the gas.

Brush the soapy solution onto the hose and all

joints. If bubbles appear you have a leak, which

must be rectiﬁed before use.

Retest after ﬁxing the fault.

Turn OFF the gas at the cylinder after testing.

If leakage is detected and cannot be rectiﬁed.

Do not attempt to cure leakage but consult

your gas dealer.

Lighting your barbecue

Lighting Instructions:

1. Connect the Needle valve to the appliance

by screwing the injector on the end of the

gas tap into the end of the burner tube in

the right hand end of the barbecue. Turn the

needle valve clockwise to “OFF” position.

2. Connect the regulator to the gas bottle. Turn

the gas supply “ON” at the regulator. Check

with the use of soapy water for any gas leak-

age between the bottle and the regulator.

3. Open the hood, turn on needle valve, whilst

applying a match to the lighting hole in the

right hand side of the barbecue. Turn the

needle valve anti-clockwise to the “Full rate”

position. Keep the match in the lighting

hole until the burner lights. Do not hold the

match in the hole for longer than 5 seconds.

4. If the burner has not lit wait 5 minutes and

repeat step 3.

5. Adjust the heat by turning the needle valve

to the High /Low position.

6. To turn the barbecue ‘OFF’ turn the cylinder

valve or regulator switch to the ‘OFF’ posi-

tion and then turn the needle valve on the

appliance clockwise to the ‘OFF’ position.

Warning: If the burner fails to ignite, turn the

control knob off (clockwise) and also turn the

cylinder valve off. Wait ﬁve minutes before at-

tempting to relight with ignition sequence.

Before cooking for the ﬁrst time, operate the

barbecue for about 15 minutes with the lid

closed and the gas turned on HIGH. This will

“heat clean” the internal parts and dissipate

odour from the painted ﬁnish.

Clean your barbecue after each USE.

DO NOT use abrasive or ﬂammable cleaners,

as it will damage the parts of the product and

may start a ﬁre.

Clean in warm soapy water.

WARNING: Accessible parts may be very hot.

Keep young children away from the hot appli-

ance at all times (even while cooling down!). It is

recommended that protective gloves (e.g. oven

gloves) be used when handling particularly hot

components.

Cleaning and care

CAUTION: AII cleaning and maintenance should

be carried out when the barbecue is cool and

with the fuel supply turned OFF at the gas cyl-

inder.

Cleaning

“Burning off” the barbecue after every use (for

approx 15 minutes) will keep excessive food

residue to a minimum.

Outside surface

Use mild detergent or baking soda and hot

water solution. Non-abrasive scouring powder

can be used on stubborn stains, then rinse with

water. If the inside surface of the barbecue lid

has the appearance of pealing paint, baked on

grease build-up has turned to carbon and is

ﬂaking off. Clean thoroughly with strong hot

soapy water solution. Rinse with water and al-

low to completely dry.

NEVER USE OVEN CLEANER.

Interior of barbecue bottom

Remove residue using brush, scraper and/or

cleaning pad then wash with a soapy water so-

lution. Rinse with water and allow to dry.

Cooking grid

Use a mild soapy water solution. Non-abrasive

scouring power can be used on stubborn stains

then rinse with water.

Cleaning the burner assembly

Turn the gas OFF at the control knob and dis-

connect the cylinder.

Remove cooling grate.

Clean the burner with a soft brush or blow clean

with compressed air and wipe with a cloth.

Clean any clogged ports with a pipe cleaner or

stiff wire (such as an opened paper clip).

Inspect burner for any damage (cracks or

holes). If damage is found, replace with a new

burner. Reinstall the burner, check to ensure

that the Gas valve oriﬁces are correctly po-

sitioned and secured inside the burner inlet

(venturi).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boretti PICCOLINO in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boretti PICCOLINO Manual

Product: