Manual Boretti BVW 96 (page 90 of 96) (English, German, Dutch, French)

534008

Zoom out

Zoom in

1/96

Water connection

Water inlet connection

This appliance can be connected to either a

hot (max. 60°) or cold water supply.

With a hot water supply you can have a sig-

nificant reduction of energy consumption.

This however, depends on how the hot water

is produced. (We suggest alternative sources

of energy that are more environmentally

friendly as e.g. solar or photovoltaic panels

and aeolian).

For making the connection itself, the cou-

pling nut fitted to the appliance water inlet

hose is designed to screw onto a 3/4" thread

spout or to a purpose made quick-coupling

tap such as the Press-block.

The water pressure must be within the limits

given in the 'Technical data'. Your local Wa-

ter Authority will advise you on the average

mains pressure in your area.

The water inlet hose must not be kinked,

crushed, or entangled when it is being con-

nected.

The locknut must be correctly fitted to avoid

water leaks.

If the appliance is connected to new pipes or

pipes which have not been used for a long

time, you should run the water for a few mi-

nutes before connecting the inlet hose.

Do not use connection hoses which

have previously been used on an old ap-

pliance.

This appliance has been fitted with safe-

ty features which will prevent the water

used in the appliance from returning

back into the drinking water system. This

appliance complies with the applicable

plumbing regulations.

Water inlet hose with safety valve

After connecting the double-walled water in-

let hose, the safety valve is next to the tap.

Therefore the water inlet hose is only under

pressure while the water is running. If the wa-

ter inlet hose starts to leak during this oper-

ation, the safety valve cuts off the running

water.

Please take care when installing the water

inlet hose:

• The electrical cable for the safety valve is

in the double-walled water inlet hose. Do

not immerse the water inlet hose or the

safety valve in water.

• If water inlet hose or the safety valve is

damaged, remove the mains plug imme-

diately.

• A water inlet hose with safety valve must

only be replaced by the Service Force

Centre.

Warning! Dangerous voltage

Water drain connection

The end of the drain hose can be connected

in the following ways:

1. To the sink outlet spigot, securing it to the

underside of the work surface. This will

prevent waste water from the sink run-

ning into the machine.

2. To a stand pipe provided with venthole,

minimum internal diameter 4 cm.

max 85 cm

min 40 cm

max 400 cm

The drain hose can face either to the right or

left of the dishwasher

Ensure the drain hose is not bent or squash-

ed as this could prevent or slow down the

discharge of water.

The sink plug must not be in place when the

machine is draining as this could cause the

water to syphon back into the machine.

If you use a drain hose extension, its internal

diameter must be no smaller than the diam-

eter of the hose provided.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boretti BVW 96 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boretti BVW 96 Manual

Product: