534012

Boretti BPK-45 Manual

14
Zoom out
Zoom in
Previous page
1/38
Next page
26 27
ENGB
9. DISPENSING HOT WATER
To dispense hot water, suitably position the water/steam
nozzles, see Fig. 10.1
• Position a container below the water/steam nozzle.
• Press the hot water button.
• Press the START button with 10 seconds from
making your selection. The water will be dispensed
as long as the button is pressed; to stop dispensing,
release the button.
ATTENTION: if the start button is not pressed
within 10 seconds, the function is disabled. If
you wish to dispense a beverage, you will have
to repeat the procedure.
We recommend that you do not dispense hot
water immediately after dispensing steam.
10. DISPENSING STEAM
To dispense steam, press the steam button. The
corresponding indicator light will ash for 15 seconds.
As soon as the indicator light stops ashing and remains
steady on, the machine is ready to dispense steam.
• Place the container with the liquid to be heated below
the steam nozzle.
• Completely immerse the nozzle in the liquid to be
heated.
• Press the START button within 10 seconds from
making your selection and wait for the steam to come
out.
ATTENTION: if the start button is not pressed
within 10 seconds, the function is disabled. If
you wish to dispense a beverage, you will have
to repeat the procedure.
The steam will continue to ow until you release the
START button.
If you are preparing milk for a cappuccino, we
suggest that you agitate the
milk container for better results.
11. PROGRAMMING THE QUANTITY OF
GROUND COFFEE
You can choose from three strengths of coee:
• light;
• medium;
• strong.
To change from one type of coee to the other, just
press the button as shown in Fig. 12.1. The LED for the
selected coee will light (in Fig. 12.2, light coee).
two LEDs ash for its duration.
• press the START/STOP button again when the
desired quantity is reached.
Restoring the factory settings
When it leaves the factory, the machine is calibrated
for Italian-style espresso coffee and German-style
stretched coffee.
• If you need to restore these standard values, you
must place the machine in standby and press the
coee regulation button for 6 seconds.
• You will see all the LEDs, except on/o, ash for 5
seconds; after that time, the board has stored the
default values.
• Press the on button and the selections will now use
the factory values.
The standard values are only relative to the
quantity of water necessary for each single
dose.
FOR EXPERT USERS ONLY:
PROGRAMMING THE GRINDING TIME
The grinding time for strong coee is programmable and
medium and light coee are calibrated accordingly.
To enter programming mode, when the machine is in
standby mode:
• press the START/STOP button for 5 seconds; the
LED s on the upper left line light up to indicate the
grinding time;
• to increase the time, press the coee regulation
button and to, decrease it, the START/STOP button.
At the end of the operation, just press the on/o
button to exit and conrm the changes.
12. PROGRAMMING THE QUANTITY OF
COFFEE IN THE CUP
All the cycles have a preset quantity, except for water
and steam.
The machine is already calibrated at the factory to
dispense the ideal quantity of coee for an espresso
cup.
While dispensing the beverage, you can stop dispensing
before the preset time by pressing the START/STOP
button.
In addition, while dispensing the beverage, you can
obtain a greater quantity than the preset by holding
down the START key continuously within 3 seconds
from the end. This activates the dispensing of additional
beverage until the button is released, up to a maximum
of 20 seconds.
The procedure for programming the quantity of coee,
and other beverages, in the cup is as follows:
• press the coee key for 5 seconds until the LED
ashes.
• press the START/STOP key to start dispensing. The
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Boretti BPK-45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Boretti BPK-45 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info