533759

Boretti BIZ4 Manual

91
Zoom out
Zoom in
Previous page
1/96
Next page
D
EN
43
Boretti cannot be held responsible for any incident resulting from incorrect connection
or which could arise from the use of an appliance which has not been earthed
or has been equipped with a faulty earth connection.
Caution!
This appliance is only to be connected to a network 230 V~ 50 Hz.
Always connect the earth wire.
Respect the connection diagram.
The connection box is located underneath, at the back of the hob casing. To open the cover use a
medium screwdriver. Place it in the slits and open the cover.
Mains Connection Cable diameter Cable Protection calibre
230V~1P+N 50Hz 1 Phase + N 3 x 2,5 mm² H 05 VV - F 25 A *
H 05 RR - F
400V~2P+N 50Hz 2 Phase + N 4 x 1,5 mm² H 05 VV - F 16 A *
H 05 RR - F
230V~2P+2N 50Hz 2 Phase + 2N 5 x 1,5 mm² H 05 VV - F 16 A *
H 05 RR - F
* calculated with the simultaneous factor following the standard TN 60 335-2-6/1990
Connection of the hob
Setting up the configurations:
For the various kinds of connection, use the
brass bridges which are in the box next to the
terminal
Monophase 230V~1P+N
(not for the Netherlands!)
Put the 1st bridge between terminal 1 and 2,
the 2nd between 3 and 4.
Attach the earth to the terminate “earth”, the
neutral N to terminal 3 (or 4), the Phase L to
one of the terminals 1 or 2.
Biphase 400V~2P+N
Put a bridge between terminal 3 and 4.
Attach the earth to the terminate “earth”, the
neutral N to terminal 3 (or 4), the Phase L1
to the terminals 1 and the Phase L2 to the
terminal 2.
Biphase 230V~2P+2N
Attach L1 to terminal 1, L2 to terminal 2, N1
to terminal 3, N2 to terminal 4 and earth to
terminal “earth”
Caution! Ensure that you correctly attach the
wires and the bridges. Tighten the screws
properly. Before making the connection, we
strongly advise you to locate the phase(s), neu-
tral and earth on the mains. Note: the bridges
between terminals 4-5 and between terminals
1-2 were installed during the factory check.
… 91 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Boretti BIZ4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Boretti BIZ4 in the language / languages: Dutch, French as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info