Manual Boretti AK 10 (page 20 of 24) (English, German, Dutch, Danish, French, Italian)

121721

Zoom out

Zoom in

1/24

20 AK 10

Italiano English Français

E - CONNESSIONE ELETTRICA ALLA

RETE:

- Verificare che la tensione di rete sia

adeguata a quella richiesta par l'ali-

mentazione della cappa come in-

dicato sulla targhetta applicata al-

l'interno dell' apparecchio.

- Montare sul cavo una spina a nor-

ma e adeguata al carico da sop-

portare oppure, nel caso di colle-

gamento diretto alla rete, interpor-

re tra la rete e l'apparecchio un in-

terruttore bipolare a norma e di po-

tenza adeguata con apertura mini-

ma fra i contatti di 3mm.

- Il cavo di terra giallo/verde (se pre-

sente) non deve essere interrotto.

F - CONTROLLO FUNZIONALE:

- Verificare l'accensione del motore

nelle varie velocita' e l'illuminazio-

ne.

G - POSIZIONAMENTO CAMINI

- Infilare il camino telescopico supe-

riore all’ interno del camino telesco-

pico inferiore (Fig.10).

- Posizionare il camino telescopico

inferiore sul corpo cappa.

- Sollevare verso l’alto, fino all'altez-

za desiderata, il camino telescopi-

co superiore e fissarlo alla staffa uti-

lizzando le due viti in dotazione

M3,9 x 9,5 (Fig.11).

E - HOW TO CONNECT TO THE ELEC-

TRICAL MAIN:

Check to see that the main voltage

complies with the one required by

the hood, which is indicated on the

tag that is applied on the internal

side of the appliance.

Assemble a suitable plug on the wire

or insert a proper power two-pole

switch if it is to be directly connected

to the main with a 3mm minimum

opening between contacts between

the main and the appliance. All the

above-mentioned electrical parts

must comply with the current stand-

ards.

The yellow/green earthing cable (if

included) must not be interrupted.

F - OPERATING CHECKS:

Check lights and motor start-up in

the several speeds.

G - HOW TO POSITION THE STACKS:

- Slide the upper telescopic stack in-

side the lower telescopic stack (Fig.

10).

- Position the lower telescopic stack

on the hood case.

- Raise the upper telescopic stack to

the height desired and fix it by

means of the two M3.9 x 9.5 screws

included in the supply (Fig. 11).

E - CONNECTION ELECTRIQUE AU RE-

SEAU:

Vérifier que la tension de réseau

corresponde à celle qui est deman-

dée pour l’alimentation de la hotte

comme indiqué sur la plaque située

à l’intérieur de l’appareil.

Sur le câble monter une fiche selon

les règles, indiquée pour la charge

à supporter ou, dans le cas de

liaison directe avec le réseau, pla-

cer, entre le réseau et l’appareil, un

interrupteur bipolaire selon les rè-

gles et avec une puissance adé-

quate et une ouverture minimum

entre les contacts de 3mm.

Le câble de terre jaune/vert (s’il

existe) ne doit pas pas être inter-

rompu.

F - CONTROLE FONCTIONNEL:

Vérifier l’allumage du moteur dans

les différentes vitesses et l’illumi-

nation.

G - POSITIONNEMENT CHEMINEES

- Enfiler la cheminée télescopique à

l’intérieur de la cheminée télesco-

pique inférieure (Fig. 10)

- Positionner la cheminée télescopi-

que inférieure sur le corps de la

hotte

- Soulever la cheminée télescopique

supérieure vers le haut, jusqu’à la

hauteur souhaitée et la fixer à la

bride en utilisant les deux vis en

dotation M3,9 x 9,5 (Fig.11).

Fig. 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boretti AK 10 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 5,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boretti AK 10 Manual

Product: