714520
29
Zoom out
Zoom in
Previous page
1/44
Next page
EN
29
Assembly
www.bora.com
1
L1 L2 L3
2 3 4
N PE
220 - 240 V~
220 - 240 V~
220 - 240 V~
Fig. 6.36 Connection diagram 3-phase connection
1
L1 L2
2 3 4
N PE
220 - 240 V~
220 - 240 V~
Fig. 6.37 Connection diagram 2-phase connection
1
L1
2 3 4
N PE
220 - 240 V~
Fig. 6.38 Connection diagram 1-phase connection
3
3
1
1
2
Fig. 6.39 Electrical connections of the cooktop
[1] Bore holes
[2] Power supply
[3] Cable mounting clip
Based on the relevant connection diagram (see
Figs. Connection diagram), connect the power supply
line to the power connection [2] on the cooktop with
integrated cooktop extractor.
For one- or two-phase-connections install the relevant
contacts with the BKAS connector clip (included in the
scope of delivery).
Fasten the cable mounting clips [3] in the designated
bore holes (1) either on the left or right hand side for
the cable routing to the rear.
Make sure that the cable is not clamped or damaged
and cannot touch any hot parts of the cooktop.
Verify that the installation was done correctly.
Switch on the main switch/automatic circuit breaker.
Put the cooktop extractor into operation (see the
Operation chapter).
Check all the functions are working correctly.
Device power management
(total power reduction)
The total power of the device can be reduced to 4.4
KW for initial commissioning, if the required electrical
power cannot be provided at the site of installation.
The connection must always be equipped with a fuse
protection of at least 20 A.
Programming the device power management
For the programming process, the device must not be
switched on and the childproofing feature must not be
active. Program the cooktop within 2 minutes after the
cooktop is supplied with power.
For programming, press all 4 cooking zone selection
buttons at the same time for 3 seconds.
The display will show 7.4 (factory setting).
By pressing the or button, set the reduced
total power consumption to 4.4.
To save your settings, press all 4 cooking zone selec-
tion buttons at the same time for 3 seconds until an
acoustic signal sounds.
The acoustic signal indicates that the setting is saved
and the cooktop switches itself off.
If the cooktop is switched on again, it is ready for use.
6.9 Handover to user
Once installation is done:
Explain the important functions to the user.
Explain all safety-relevant aspects of operation and
handling to the user.
Provide the user with the accessories and operating
and installation instructions to be kept in a safe place.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bora BIAS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bora BIAS in the language / languages: English as an attachment in your email.

The manual is 7,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bora BIAS

Bora BIAS User Manual - German - 44 pages

Bora BIAS User Manual - Dutch - 44 pages

Bora BIAS User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info