714528
37
Zoom out
Zoom in
Previous page
1/48
Next page
EN
37
Operation
www.bora.com
Resetting the filter service display
If the activated charcoal filter has been replaced (with
recirculation only) and the stainless steel grease filter
has been cleaned, it will be necessary to reset the filter
service display.
Switch on the cooktop with integrated cooktop
extractor.
The fan display will show a flashing
F
.
Press the selection button on the cooktop extractor for
at least 4 seconds until a flashing
0
appears.
After a few seconds, a solid
0
will be displayed.
The filter service display has been reset.
7.5 Saving energy
Follow all of the energy-saving tips to use the cooktop
with integrated cooktop extractor in an energy-efficient
manner.
When purchasing cookware, pay attention to the
diameter of the base as the upper diameter of the pot
is usually specified. The diameter of the base is often
smaller.
Use pressure cookers. Due to the closed cooking
chamber and the overpressure, these save a great deal
of time and energy. The short cooking time also helps
preserve vitamins.
Make sure there is sufficient liquid in the pressure
cooker. An empty pot which is still being heated can
lead to overheating. This can damage both the cooking
zone and the pot.
If possible, always seal cookware using a suitable lid.
Choose a suitable size of cookware for the amount
of food you are cooking. A big pot that is barely filled
requires a lot of energy.
7.3.6 Switching off the automatic cooktop
extractor function
Press the selection button for the cooktop extractor.
Press the multi-function button .
The automatic cooktop extractor function is deactivated.
7.3.7 Automatic after-run
Press the selection button for the cooktop extractor.
The fan display lights up more brightly.
Select power level
0
The power level
n
is shown on the display.
The cooktop extractor switches off automatically after
20 minutes.
7.3.8 Switching off the automatic after-run
early
Press the selection button on the cooktop extractor
while the automatic after-run is active.
The automatic after-run is switched off.
7.3.9 Switching off the cooktop extractor
Press the selection button for the cooktop extractor.
The fan display lights up more brightly.
Select power level
0
.
The power level
0
is shown on the display.
Press the selection button for the cooktop extractor
again.
The device switches off.
or
Press the on/off switch to switch off the device.
INFO If the automatic cooktop extractor function is
activated when switching off, it will remain active
the next time the extractor is switched on.
7.4 Pay attention to the filter service
display
If
F
appears on the fan display, this means the service life of
the activated charcoal filter has expired (with recirculation
only) and the stainless steel grease filter needs to be
thoroughly cleaned:
Press the selection button for the cooktop extractor.
Press any button.
0
is shown in the fan display.
Changing the filter
Switch off the cooktop with integrated cooktop
extractor.
Observe all warnings that are described in the Cleaning
chapter.
Replace the activated charcoal filter.
Clean the stainless steel grease filter, the air inlet nozzle,
the air guiding housing and the housing base.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bora BFIU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bora BFIU in the language / languages: English as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bora BFIU

Bora BFIU User Manual - German - 52 pages

Bora BFIU User Manual - Dutch - 52 pages

Bora BFIU User Manual - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info