Manual Bompani BO643 (page 19 of 92) (English, Dutch, French, Italian)

476985

Zoom out

Zoom in

1/92

- Avoid sharp bends in the pipe and keep it

well away from hot surfaces.

References to the regulations covering the

gas connection to the appliance: ISO 7-1.

ADAPTING TO DIFFERENT TYPES OF

GAS

If the cooker is not already preset to operate

with the type of gas available, it must be con-

verted. Proceed as follows:

- Replace the injectors (see table on page

17);

- regulate the primary air flow;

- regulate the minimum settings.

N.B.: every time you change the type of gas,

indicate the new type of gas on the serial

number label.

REPLACING THE HOB BURNER INJEC-

TORS (fig. 4)

- Lift off the pan stands, flame caps and burn-

ers

- unscrew the screws which secure the hob

(if any), lift it at the front and rest it against

the lid, fixing it with adhesive tape;

- remove the mixer pipes and replace the

injectors using a 7 mm socket wrench.

REPLACING THE OVEN BURNER INJEC-

TOR (Fig. 5)

- Loose the screw securing the oven bottom;

- remove the oven bottom (push back and

raise);

- remove the oven burner, after taking out its

fixing screw;

- replace the injector, using a 7 mm socket

wrench.

REPLACING THE GRILL BURNER INJEC-

TOR (Fig. 6)

- Remove the burner after taking out the two

screws which secure it;

- replace the injector using a 7 mm socket

wrench.

IMPORTANT:

- Never over-tighten the injectors;

- after replacing, check that all the injectors

are airtight.

REGULATING THE BURNER AIR

Refer to the table below (indicative values)

for regulation of the gap H in mm (fig. 4 for

the hob, fig. 6 for the grill).

Check operation of the burner:

- Ignite the burner at maximum flame;

- the tongue of the flame must be clear and

with no yellow tip, and must adhere closely

to the burner. If too much air is supplied,

the flame detaches from the burner and

may be dangerous. If the air supply is in-

sufficient, the flame has a yellow tip and

soot may form.

SETTING HOB BURNER MINIMUM LEV-

ELS

If the cooker is to work on bottled gas (bu-

tane/propane), the tap by-pass must be

screwed right down.

The cooker may be equipped with type A

taps, with by-pass inside (accessed by in-

serting a small screwdriver into the rod) or

type B taps, with by-pass on the outside on

the right (accessed directly). See figure 7.

If the cooker is to work on natural gas, pro-

ceed as follows for both types of tap:

- Ignite the burner at maximum flame;

- pull off the knob, without using a lever

against the control panel, which might be

damaged;

- access the by-pass with a small screwdriver

and back off by about 3 turns (turning the

screwdriver anti-clockwise);

- turn the tap rod anti-clockwise again until it

stops: the burner will be at maximum flame;

Burner G20 20mbar G30 28-30mbar

G31 37mbar

Auxiliary 3 4

Semi-rapid 3 4

Rapid 4 6

Ultra-rapid 5 6

Oven -- --

Grill 3 7

Installation

334766-01 7-02-2003, 15:5319

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bompani BO643 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 0,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bompani BO643 Manual

Product: