19
Connected Wattage
The total power consumption of this device can be up to 2200 W.
With this connected load a separate supply line protected by a
16 A household circuit breaker is recommended.
CAUTION:OVERLOAD!
• If you use extension leads, these should have a cable
cross-section of at least 1.5 mm².
• Do not use any multiple sockets, as this device is too
powerful.
Switching on/off
Switching on: Press the toggle switch downwards. The
indicator light in the switch lights up.
Switching off: Press the toggle switch upwards. The indicator
light in the switch goes off.
Use
NOTE:
• Always use fresh water.
• Do not consume the water if it has been in the kettle for
more than one hour.
• Also do not constantly reheat cooled water.
• Always pour out stagnant water.
1. Place the machine on a at surface.
2. Press the button in the handle to open the kettle.
3. Then ll in the water (max 1.7 Litre). You can read the lling
level on the water level indicator of the kettle.
4. Close the lid.
5. Place the kettle ush on the base.
6. Only connect the machine to a properly installed 230 V~,
50 Hz safety socket.
7. Switch on the kettle by pressing the switch. The control
lamp in the switch will light up.
Switching off/Interrupting Operation
There are two ways to stop/interrupt the boiling process:
a) The appliance switches off automatically after the water
has boiled.
b) Press the switch upwards to interrupt or to nish boiling.
The control light in the switch will go out.
CAUTION:
• Do not remove the appliance from the base without
switching it off beforehand. As long as the switch is
pressed down, the kettle is turned on.
• Always switch the device off before you remove it from
the base! Please also ensure that it is switched off when
you put it back on the base!
WARNING:DANGEROFSCALDING!
• When pouring the water out, keep the lid closed.
• During operation the housing becomes hot. Do not touch
it and allow the device to cool down before storing it away.
• Remove the mains plug.
• Emptying the water container.
MainsCableTake-upDevice
The mains cable can be wound up on the base.
Cleaning
WARNING:
• Always turn the device off before cleaning it and remove
the mains plug. Wait until the device has cooled down.
• Never immerse the device or the base in water or other
liquids.
CAUTION:
• Do not use any wire brush or other abrasive objects.
• Do not use any acidic or abrasive detergents.
• Rinse the water container out with clean water. Then dry it
off with a cloth.
• Clean the housing after use with a slightly damp cloth.
• A permanent lter is located at the spout opening. To clean
the lter, pull it out when the lid is open. Rinse it out under
running water. If necessary, clean it with a nylon brush.
Reinsert the lter. To do so, use the guides on the inside of
the kettle.
Decalcication
• The frequency of the decalcifying operation depends on
the hardness of the water and on how often the appliance
is used.
• If the machine switches off before the water boils, it prob-
ably needs to be decalcied.
• Please do not use vinegar but a commercially available
decalcication agent on the basis of citric acid. Only use
the quantities stated in the instructions.
NOTE:
After descaling the device boil fresh water in it several times
(approximately 3-4 times) in order to remove any residues.
Do not consume this water.
Troubleshooting
• Itisnotpossibletoswitchthemachineon.
Possible Cause:
After being used without or with too little water the machine
has not cooled down sufciently.
Remedy:
Allow the machine to cool down for 15 min.
• Themachineswitchesoffbeforethewaterhasboiled.
Possible Cause:
The heating element is covered in scale or the electrical
circuit of the power socket is overloaded.
