688012
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
Delivery scope
Delivery scopeDelivery scope
Delivery scope
1x Inlet hose, 1x bottom plate incl. 3x fixing clips,
2x transport locking covers, 1x hose retaining sheet
Installation
InstallationInstallation
Installation
WARNING:
WARNING:WARNING:
WARNING:
The unit must not be connected to the mains during
installing. Otherwise there is da
dada
dan
nn
nger to life
ger to lifeger to life
ger to life or elec
elecelec
electric
tric tric
tric
shock hazard
shock hazardshock hazard
shock hazard!
CAUTION:
CAUTION:CAUTION:
CAUTION:
For a correct operation the appliance must be con-
nected properly. The specifications for water supply
and drain as well as the electrical connection must
fulfill the required criteria.
Install the bottom plate
Install the bottom plateInstall the bottom plate
Install the bottom plate
The bottom plate is included in the scope of delivery
between the appliance rear and the packaging.
Align the plate in its
intended position
underneath the device and
fix it with the enclosed
clips.
Remove the transport locking screws
Remove the transport locking screwsRemove the transport locking screws
Remove the transport locking screws
CAUTION:
CAUTION:CAUTION:
CAUTION:
Before using, all transport locking screws must be
removed from the appliance back. Otherwise it
may cause serious damages.
Keep the transport locking screws for later use /
transport. Never transport the appliance without
properly attached transportation safety!
Remove the transport lock-
ing screws with a wrench.
Insert the supplied
transport locking covers.
Installation location
Installation locationInstallation location
Installation location
The site should be located near the water inlet
and outlet, as well as near a properly grounded
power socket.
Good ventilation around the appliance is required,
in order to dissipate the heat properly. Sufficient
clearance must be created for this purpose.
The clearance to the top must be created so, that
the unit lid can open without being impeded.
Make sure that the floor on which the appliance is
installed, is even, heat-resistant and clean.
Take care of a solid and horizontal position of the
appliance. If the appliance is not horizontally lev-
eled, adjust the feet accordingly (see “Adjust the
feet”).
Power cord and water hoses may not kinked or
squashed.
The wall socket must be freely accessible.
Avoid the installation:
Avoid the installation:Avoid the installation:
Avoid the installation:
- near heaters, next to a stove, direct sunlight
or any other heat sources;
- at locations with high humidity (e.g. out-
doors), as metal parts would be susceptible
to corrosion under such circumstances;
- in rooms where the temperature could drop
below freezing. Do not expose the appliance
any weather.
- near volatile or flammable materials (e.g.
gas, fuel, alcohol, paint, etc.).
Adjusting the feet
Adjusting the feetAdjusting the feet
Adjusting the feet
CAUTION:
CAUTION:CAUTION:
CAUTION:
The feet must never be removed. Do not restrict the
floor clearance through carpets, strips of wood or
similar. Danger of heat accumulation!
Danger of heat accumulation!Danger of heat accumulation!
Danger of heat accumulation!
Use the wrench to loosen the
lock nuts. Rotate the feet to
change the height.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann WA 5726 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann WA 5726 in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann WA 5726

Bomann WA 5726 User Manual - German - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info