552030
6
Zoom out
Zoom in
Previous page
1/20
Next page
6
09/2013
I
NSTALLATION
Remove the transport bolts
Before using this washing machine, the transport bolts must be removed from the backside of the
machine. Loosen all bolts with spanner and then remove them and keep the transport bolts properly
for future use/transport. Plug the holes with the transit bolts caps supplied.
- Once unscrewed the screws pull out the locking screws including a bushing and spacer as shown
in Figure 1-3.
-
Close up the holes with the supplied caps as shown in Figure 4.
Installation – place requirements -
- The device must be installed in a clean place, where dirty does not build up.
- A concrete floor is the most suitable installation surface for a washing machine, being far less
prone to vibration during the spin cycle than wooden floorboards or a carpeted surface.
- The machine must be level and securely positioned.
- Do not expose the device to direct sunlight.
- Do not place near heaters, next to a stove or any other heat sources.
- Avoid installation at locations with high humidity (e.g. outdoors), as metal parts would be suscepti-
ble to corrosion under such circumstances.
- Do not install in rooms where the temperature could drop below freezing. Do not expose the device
any weather.
- Do not place the device near volatile or combustible materials (e.g. gas, fuel, alcohol, paint, etc.).
- Only place on a steady and safe surface in order to reduce vibration and noise to a minimum.
- If the ground is evidently uneven (the maximum allowed tilt angle is 2°), it must be balanced; oth-
erwise the unit is wrong, vibrates or moves.
- If the floor is uneven, adjust the adjustable feet.
- Good ventilation around the unit is required so the heat can be derived correctly. The distance be-
tween the machine and wall must be more than 10 cm.
- The mains plug must be freely accessible.
WARNING: Should the bolts
aren’t removed; there could be
serious damages during operation.
Transport-
sicherungen
NOTE:
Keep the transit bolts for future transportation. Whenever the ma-
chine is transported, the transit bolts must be refitted.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann WA 5712 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann WA 5712 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann WA 5712

Bomann WA 5712 User Manual - German - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info