552034

Bomann WA 5612 Manual

6
Zoom out
Zoom in
Previous page
1/14
Next page
6
06/2012
I
NSTALLATION
Remove the Transit Bolts
Before using this washing machine, transport bolts must be removed from the backside of this ma-
chine. Loosen all bolts with spanner and then remove them and keep the transport bolts properly for
future use/transport. Plug the holes with the transit bolts caps supplied.
WARNING: Should the bolts aren’t removed, there could be serious damages during operation.
Location
- The device must be installed in a clean place, where dirty does not build up.
- Do not expose the device to direct sunlight.
- Do not place near heaters, next to a stove or any other heat sources.
- Avoid installation at locations with high humidity (e.g. outdoors), as metal parts would be suscepti-
ble to corrosion under such circumstances.
- Do not install in rooms where the temperature could drop below freezing. Do not expose the device
any weather.
- Do not place the device near volatile or combustible materials (e.g. gas, fuel, alcohol, paint, etc.).
- Only place on a steady and safe surface in order to reduce vibration and noise to a minimum.
- If the ground is evidently uneven (the maximum allowed tilt angle is 2°), it must be balanced, oth-
erwise the unit is wrong, vibrates or moves.
- If the floor is uneven, adjust the adjustable feet.
- A good ventilation around the unit is required so the heat can be derived correctly. A distance of
approx. 10 cm from the wall is required.
- The mains plug must be freely accessible.
Feet Adjustment
Take care to a firm and horizontal position of the dryer. If the
machine moves adjusts the feet. Loosen the locknuts with a
spanner.
Adjust the feet: to lower the dryer by turning right and to
ascend it by turning left. Tighten the locknut with the spanner
after insuring the device is leveled.
Once the position is fixed, you need to check the stability.
If not, repeat the action till it is leveled.
NOTE:
- The locknuts must be tightened after adjustment. Any looseness can cause vibration and noise.
- The feet must never be removed. Do not restrict the floor clearance through deep pile carpets,
strips of wood or similar. This might cause heat build-up which would interfere with the operation of
the appliance.
Water Connection
Install the Water Drain Hose
There are two ways to place the end of drain hose:
- Hang into a sink or trough.
- Connect it to the branch drain pipe of the trough.
If the outlet spigot has not been used before, remove any blanking plug that may be in place.
Push the drain hose onto the spigot and secure with a clip if required, ensure a loop is formed in the
drain hose to prevent waste from the sink entering the washing machine.
If you need a drain hose extension, make sure to use a similar drain hose, but it must be no longer
than 4 meters; otherwise the washing effect could be reduced.
Locknuts
Adjustable feet
… 6 …


Need help? Post your question in this forum.

Forumrules
1

Forum

bomann-wa-5612

Reset search

  • Was washing and sadly the machine stoped n the power went off for days it still won’t start Submitted on 17-1-2022 at 22:19

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann WA 5612 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann WA 5612 in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann WA 5612

Bomann WA 5612 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info