686434
18
Zoom out
Zoom in
Previous page
1/26
Next page
18
MWG3001HEB_IM 12.07.2018
Installation Instructions
This microwave oven must be installed in a tall cupboard. Please note the
following instructions:
Remove everything that is fragile from the adjacent cupboards.
For the installation, the cupboard must meet the following conditions:
- The cupboard must not have any cracks, splinters or other damages.
All joints must be stable.
- The cupboard must be designed to support at least 40 kg.
- The microwave oven must be installed at a height of at least 85 cm.
- The rear wall of the cupboard must be removed to allow sufcient
ventilation of the microwave oven.
- The side walls of the cupboard must be at least 19 mm thick.
- The installation depth of the cupboard has to be at least 550 mm.
It is important that there is a power socket within reach of the appli-
ance´s power cable.
Check that the mains voltage is correct before you connect the plug
to the socket. You will nd the information about the appliance on the
rating label for specications.
Only connect the appliance to a tested socket.
The power socket must be easily accessible so that the plug can be
quickly removed in case of an emergency.
Important! Do not plug in the appliance until the installation has been
completed!
Further information and instructions can be found on the drilling tem-
plate provided.
WARNING:
Adhere to the dimensions given in the instructions.
Only use the included installation accessories.
Screws which are screwed in too deeply (or are too long) can dam-
age the appliance or represent a potentially fatal safety hazard.
Dimensions of the Cupboard
Prepare a built-in cupboard / niche according to the following dimensional
drawing Diagram 1.
1
Installation (Steps. 2 to 4)
2
This gure is an example only. The dimensions may vary as
these depend on the thickness of the wall cabinet.
The original drilling template is enclosed with the appliance.
Proceed as follows:
1. Check if your cabinet has a smooth, at bottom and right
size, and tape the template onto the bottom plane of
cabinet.
2. Make sure the center line of the template is in the middle of
the cabinet.
NOTE:
Make sure the front edge of template is even with the
cabinet front edge.
3. Make marks on the bottom plane of cabinet according to
the hole “X” of the template.
CAUTION:
Do not drill holes in the bottom cabinet.
4. After make marks according to the instruction, remove the
template.
5. Mount the standing feet at the marked positions.
3
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann MWG 3001 HEB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann MWG 3001 HEB in the language / languages: English, German as an attachment in your email.

The manual is 2,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info