814350
28
Zoom out
Zoom in
Previous page
1/32
Next page
28
Cleaning / replacing the door seal
Regularly check the seal for dirt, damage and air
tightness!
Checking the seal for air tightness
Clamp a thin piece of paper at various points for
testing. The paper must be equally difficult to pull
through at all points.
Cleaning the gasket
Clean the gasket with clear water only!
CAUTION, grease and oil makes the seal porous
and brittle. Wipe up grease or oil immediately with
a damp, clean cloth.
Replacing the seal
Remove the contents of the appliance and, if
necessary, defrost the unit. Pay attention to how
the old gasket is attached. Most gaskets are only
plugged in.
Remove the worn gasket rubber by removing it
from the groove. Carefully clean the appliance
door and the groove below the rubber and re-
move any adhesive residue.
Attach the new rubber. If necessary, heat the
rubber seal with a hair dryer or hot water and
shape it by hand. Start pressing the gasket in one
corner and then press it around the door into the
groove provided for this purpose.
Continue to check the seal regularly for dirt and
damage!
Defrosting
CAUTION:
Never use metal objects (e.g. knifes) to remove ice
from the evaporator, it can be damaged.
During the defrosting process in the fridge, the
water drops drain off at the back wall of the cooling
chamber. The thaw water running through a channel,
is collected in a drip tray located on the compressor,
from which it then evaporates. Make sure that the
defrost water drain channel does not become
clogged. A slight formation of ice on the interior rear
wall during operation is normal.
A permanently high power level can lead to in-
creased ice formation
set a lower power level and
wipe the interior of the appliance dry.
To achieve better cooling and to save energy,
defrost the freezer regularly:
To start the defrosting process, disconnect the
appliance from the power supply.
Remove the appliance content and keep covered
at a cool location.
When the ice has melted, wipe the condensate
away and dry the appliance interior.
Then you may restart the appliance by connecting
the plug and turning the temperature control.
Changing the light
CAUTION:
Do NOT remove the cover of the light. The LED light
may be replaced / repaired in case of failure / defect
only by an authorized specialist.
Replacing the door hinge
If the appliance door starts to stutter, crack or jam
when you open it, it is probably due to a worn or
damaged hinge.
It is recommended to replace all door hinges at the
same time, otherwise the next repair will soon be
beckoning.
Remove the contents of the appliance and the
movable interior parts.
Tilt the appliance backwards and block it in this
position to prevent the door from sliding out.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann KG 7352 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann KG 7352 in the language / languages: English, German as an attachment in your email.

The manual is 0.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info