652040
7
Zoom out
Zoom in
Previous page
1/24
Next page
7
Using the spacer bar
Using the spacer barUsing the spacer bar
Using the spacer bar
With this accessory you can compensate the gap between the control panel and decorative panel.
The spacer bar consists of several layers, which are connected with a click-
mechanism. Adjust the height of the spacer to the gap. To do this, remove the appro-
priate number of layers.
Fixing the decoration panel
Fixing the decoration panelFixing the decoration panel
Fixing the decoration panel
Drehen Sie die beiliegenden langen Schrauben (4 x s2) ein.
Separate the supplied Velcro strips A and B from each other.
Glue the Velcro strip A on the wooden panel (at the top and bottom) and the felt
strip B in the same heights on the appliance door.
Align the panel and the appliance front against each other and fix the panel on the
appliance door.
First remove the factory-mounted short screws (4 x s1) from the door inside.
Screw the supplied long screws (4 x s2).
Adjusting of the door spring tension
Adjusting of the door spring tensionAdjusting of the door spring tension
Adjusting of the door spring tension
After fixing the decoration panel, the door spring tension must be adjusted accordingly.
Turn the adjusting screws as needed in the clockwise or counterclockwise
direction. The steel cable tightens or loosens.
Check the door spring tension. If the door remains fully open horizontally
and can still be easily closed, the tension is correct. Otherwise do the ad-
justing again.
Connection to the water supply
Connection to the water supplyConnection to the water supply
Connection to the water supply
Connect the water inlet hose as well as the water drain hose properly. Follow the instructions that we give you
under "Water connection".
Installation to the power supply
Installation to the power supplyInstallation to the power supply
Installation to the power supply
Consider the instructions that we give you under "Electrical connection".
Adjusting the feet
Adjusting the feetAdjusting the feet
Adjusting the feet
Place the appliance in its proper position and take care that it is leveled solid and horizontal. Check this with a
spirit level.
You can adjust the back foot by the adjusting screw (a) at the center of the
appliance plinth front with an Allen key.
Adjust the front feet (b) with a screw-wrench until the dishwasher is leveled.
The maximum adjustment height of the feet is 50 mm.
Fixing the dishwasher
Fixing the dishwasherFixing the dishwasher
Fixing the dishwasher
Fix the appliance by tighten the screws from the appliance inside to the provided holes accordingly.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann GSPE 879 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann GSPE 879 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann GSPE 879

Bomann GSPE 879 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info