688021
6
Zoom out
Zoom in
Previous page
1/20
Next page
6
Take care of a solid and horizontal position of the
appliance. If the appliance is not horizontally lev-
eled, adjust the feet accordingly (see “Adjust the
feet”).
Power cord and water hoses may not kinked or
squashed.
Avoid the installation:
Avoid the installation:Avoid the installation:
Avoid the installation:
- near heaters, next to a stove, direct sunlight
or any other heat sources;
- at locations with high humidity (e.g. out-
doors), as metal parts would be susceptible
to corrosion under such circumstances;
- in rooms where the temperature could drop
below freezing. Do not expose the appliance
any weather.
- near volatile or flammable materials (e.g.
gas, fuel, alcohol, paint, etc.).
Removing the
Removing the Removing the
Removing the appliance cover
appliance coverappliance cover
appliance cover
The appliance cover can be removed and thus
reducing the device height to 81.5 cm; to place the
dishwasher under a suitable kitchen worktop.
a)
a)a)
a) Loosen the screws on the unit
back and remove the cover.
b)
b)b)
b) After removing the cover,
retighten the screws.
Adjusting the feet
Adjusting the feetAdjusting the feet
Adjusting the feet
Check with a spirit level whether the
appliance is leveled horizontally. If
the unit is not in balance, the feet
must be adjusted.
Water connection
Water connectionWater connection
Water connection
CAUTION:
CAUTION:CAUTION:
CAUTION:
The Installation of the water supply must conform
to the local laws and regulations.
The appliance is not
notnot
not suitable for hot water supply.
CAUTION:
CAUTION:CAUTION:
CAUTION:
Use the new supplied hose set to connect the
appliance to the water supply. Do not reuse old or
used connection sets.
If the water pipe is new or long time not used,
ensure before connecting to the water system,
that the water is clear and free from contamina-
tion.
Notes on inlet hose safety system (delivery scope
Notes on inlet hose safety system (delivery scope Notes on inlet hose safety system (delivery scope
Notes on inlet hose safety system (delivery scope
depending on model)
depending on model)depending on model)
depending on model)
The safety system consists of a double-walled inlet
hose. It guarantees to cut off the water supply when
leakage of the inner hose. Switching off the water
supply leads over an electronic contact.
If necessary, you can order an inlet hose safety sys-
tem from your dealer or in our online accessories
shop, www.bomann
www.bomannwww.bomann
www.bomann-
--
-germarny.de
germarny.degermarny.de
germarny.de. To order, use the
reference number found under “Technical Data”.
Connect the water inlet hose (cold water connection)
Connect the water inlet hose (cold water connection)Connect the water inlet hose (cold water connection)
Connect the water inlet hose (cold water connection)
NOTE
NOTENOTE
NOTE:
::
:
The water pressure must be between 0.04-1.0 MPa.
With higher pressure: use a pressure regulator.
Connect the water inlet hose to a
water thread with ¾“. Screw the
hose firmly in the direction of the
screw thread; pay attention for a
tight fit.
Connect the other end of the inlet
hose to the inlet valve on the appli-
ance back; pay attention for a tight
fit too.
Connect the water drain hose
Connect the water drain hoseConnect the water drain hose
Connect the water drain hose
NOTE
NOTENOTE
NOTE:
::
:
The drain hose has a length of approx. 1.5 m and
can extend with a suitable hose and connecting
piece to a length of max. 4 m.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann GSP 864 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann GSP 864 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann GSP 864

Bomann GSP 864 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info