814366
27
Zoom out
Zoom in
Previous page
1/44
Next page
27
Installation
WARNING:
The appliance must not be connected to the mains
during installing. Otherwise, there is danger to life or
electric shock hazard!
CAUTION:
For proper operation, the appliance must be con-
nected professionally. The data of inlet and outlet
as well as the electrical connection values must
meet the required criteria.
It is recommended that the installation, water
connection and electrical connection, be carried
out by a specialist.
Installation location
The site should be located near the water inlet
and outlet, as well as near a properly grounded
power socket.
Place the appliance so that all controls are easily
to reach, and the appliance door can open without
being impeded.
Take care of a solid and horizontal position of the
appliance. If the appliance is not horizontally lev-
eled, adjust the feet accordingly (see
“Adjusting
the feet”
).
Power cord and water hoses may not kinked or
squashed.
Avoid the installation:
- near heaters, next to a stove, direct sunlight or
any other heat sources;
- at locations with high humidity (e. g. outdoors),
as metal parts would be susceptible to corro-
sion under such circumstances;
- in rooms where the temperature could drop
below freezing. Do not expose the appliance
any weather.
- near volatile or flammable materials (e. g. gas,
fuel, alcohol, paint, etc.).
Removing the appliance cover
The appliance cover can be removed and thus re-
ducing the unit height to 81.5 cm; to place the dish-
washer under a suitable kitchen worktop.
a)
Loosen the screws on the unit
back and remove the cover.
b)
After removing the cover, re-
tighten the screws.
Adjusting the feet
Check with a spirit level whether
the appliance is leveled horizon-
tally. If the unit is not in balance,
the feet must be adjusted.
Water connection
CAUTION:
Installation to the water supply must be carried
out in accordance with local laws and regulations.
The appliance is not suitable for hot water supply.
Use the new hose set supplied to connect the
appliance to the water supply. Do not reuse old or
used connection sets.
If the water supply is new or has not been used
for a long time, make sure that the water is clear
and free of impurities before connecting it to the
water supply.
NOTE, the connection to the water mains may only
be made in accordance with DIN EN 1717 of the
drinking water ordinance. A suitable safety device
against drinking water contamination through back-
flow must be installed.
Notes on inlet hose safety system
(delivery scope depending on model)
The safety system consists of a double-walled inlet
hose. It guarantees to cut off the water supply when
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann GSP 7409 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann GSP 7409 in the language / languages: English, German as an attachment in your email.

The manual is 1.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info