651983
7
Zoom out
Zoom in
Previous page
1/20
Next page
Preparing the worktop for
Preparing the worktop for Preparing the worktop for
Preparing the worktop for
installation of the hob
installation of the hobinstallation of the hob
installation of the hob
The worktop must be
leveled horizontally and are
moisture.
The cut surfaces (cutout e
dges) must be sealed with special varnish,
to prevent swelling caused by humidity.
Clean and dry the worktop in the cutout area thoroughly.
CAUTION
CAUTIONCAUTION
CAUTION:
::
:
Before cutting secure the outer
cutout
Worktop cutout
Worktop cutout Worktop cutout
Worktop cutout Fig
FigFig
Fig. 2
. 2. 2
. 2
Prepare the cutout of the worktop
according to the dimen
Dimensions in mm
Installing the hob
Installing the hobInstalling the hob
Installing the hob
Before installing the hob, the supplied gasket
pending on model).
For this place the hob with the hob top on a padded surface to prevent it from damage.
NOTE
NOTENOTE
NOTE:
::
:
Depending on the model
the hob seal may
the integrity of the
hob seal and the exact fit
NOTE
NOTENOTE
NOTE: *
: *: *
: *Mounting clip
Mounting clipMounting clip
Mounting clip
and
andand
and
*
**
*M
MM
M
ounting bracket
ounting bracketounting bracket
ounting bracket
With a worktop thickness of 30 to 40 m
placed by the mounting angles 4
(
Place
the hob according to the hob
centrally into the prepared
cutout of the worktop
all four sides and that the seal
is resting
Fix the hob depen
ding on the worktop thickness by attaching the enclosed brackets 4
from the hob bottom at
the provide
Installing the oven
Installing the ovenInstalling the oven
Installing the oven
Put the appliance
with the connecting cable f
Do the connection to the hob
as well as
Insert the oven into the
cabinet opening
squeezed or twisted).
7
installation of the hob
installation of the hobinstallation of the hob
installation of the hob
leveled horizontally and are
sealed to the wall side against overflowing liquids or
dges) must be sealed with special varnish,
silicone rubber or cast raisin in order
to prevent swelling caused by humidity.
Clean and dry the worktop in the cutout area thoroughly.
cutout
edge with wide adhesive tape to avoid traces of jigsaw on the
according to the dimen
sional drawing.
Before installing the hob, the supplied gasket
must be moun
ted on the underside of the hob
For this place the hob with the hob top on a padded surface to prevent it from damage.
the hob seal may
be
already mounted during manufacturing.
hob seal and the exact fit
ting.
1
11
1
Hob 4
44
4(a)
(a)(a)
(a)
Mounting
2
22
2
Gasket 4(b)
4(b)4(b)
4(b)
Mounting
3
33
3
Worktop 5
55
5
Screw (4 pcs
ounting bracket
ounting bracketounting bracket
ounting bracket
With a worktop thickness of 30 to 40 m
m using the mounting brackets 4
(a). The front
(
b) with a worktop thickness of 28 mm.
the hob according to the hob
drawing under "Appliance
Overview" and with the connecting cable
cutout of the worktop
. Make sure that the distances to
the
is resting
on the worktop.
ding on the worktop thickness by attaching the enclosed brackets 4
the provide
d holes and fasten them with the screws.
with the connecting cable f
irst into the prepared cabinet a bit.
as well as
to the mains, see "Electrical connection".
cabinet opening
completely. Make sure that the cables
does
sealed to the wall side against overflowing liquids or
silicone rubber or cast raisin in order
edge with wide adhesive tape to avoid traces of jigsaw on the
worktop.
ted on the underside of the hob
frame (de-
For this place the hob with the hob top on a padded surface to prevent it from damage.
already mounted during manufacturing.
Check in any case
Mounting
bracket* (4 pcs)
Mounting
angle* (2 pcs)
Screw (4 pcs
)
(a). The front
brackets must be re-
Overview" and with the connecting cable
first
the
cutting are equal on
ding on the worktop thickness by attaching the enclosed brackets 4
(a) or angles 4(b)
does
not restricted (bent,
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann EHBC 555 IX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann EHBC 555 IX in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann EHBC 555 IX

Bomann EHBC 555 IX User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info