814381

Bomann EBK 7940 Manual

22
Zoom out
Zoom in
Previous page
1/32
Next page
22
A
760 mm
B
min. 50 mm
C
min. 20 mm
D
Air intake
E
Air outlet
min. 5 mm
Preparing the worktop for installation
CAUTION:
Before sawing, tape the outer edge of the cut-out
with wide tape to avoid marks from the jigsaw on the
worktop.
• The hob can be installed on a worktop with a
thickness of between min. 30 mm and max.
40 mm, it must be horizontal and sealed on the
wall side against overflowing liquids or moisture.
• The hob must be surrounded by at least 50 mm of
worktop and run parallel to the front edge of the
worktop.
• The cut surfaces (cut-out edges) must be sealed
with special lacquer, silicone rubber or casting
resin to prevent swelling due to moisture.
• The worktop in the area of the cut-out must be
thoroughly clean and dry!
Worktop cut-out
Prepare the cut-out of the worktop according to the
dimensional drawing.
Dimensions in mm
L
580
W
510
H
55
D
51
A
560
B
490
X
50
S
Seal below the hob
Installing the hob
CAUTION:
First place the front of the hob on a padded surface
to prevent damage.
Step 1: Apply sealing tape
Before installing the hob,
attach the enclosed,
self-adhesive sealing
tape (5) to the underside
of the hob frame.
• Do not use silicone! Attach the seal to the under-
side of the hob frame, leaving a gap of approx.’3
mm from the edge of the glass.
• Apply the seal around the entire circumference
and cut off any excess material. Bring the two
ends of the seal together so that they fit snugly.
Step 2: Fasten the retaining clips
Secure the hob with a total of 5 retaining clips to pre-
vent it from slipping.
1
clip
2
drilling
3
screw
• Fasten the clips (1) to the holes (2) provided on
the hob using the screws (3).
Step 3: Inserting the hob
Make sure that the distances to the cut-out are the
same on all four sides and that the seal rests on the
worktop.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann EBK 7940 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann EBK 7940 in the language / languages: English, German as an attachment in your email.

The manual is 0.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info