Manual Bomann DU 7601 G (page 19 of 28) (English, German)

687864

Zoom out

Zoom in

1/28

• Determine the position of the cooker hood central-

ly above the cooking area in accordance with the

specified safety distances.

Totally 6x mounting holes with a diameter of approx.

8 mm are necessary for the wall mounting. Insert the

supplied dowels

(Fig. 1).

(Fig. 1).(Fig. 1).

(Fig. 1).

• First mark the holes required for fixing the hood

body in accordance with the supplied drilling tem-

plate. Check the markings with a water balance

and make the holes.

- Turn in the upper screws 2x ST4*30mm for the

suspension of the hood body so far that they

project approx. 5 mm out of the wall.

• Fasten the bracket for the upper shaft termination

with the screws 2x ST4*40mm after determining

the extension length of the shaft cover.

• Before attaching the hood

(Fig.

(Fig.(Fig.

(Fig.

2)2)

- Fasten the glass screen with the screws

4x M4*20mm in the screw insert made of rub-

ber together with washers on the hood body.

- Affix the connecting piece with inserted non-

return valves from the top of the extraction

duct with the screws 2x ST4*8mm.

Insert the two non-return valves by lightly

bending them from above into the connecting

piece

(Fig. 2a)

(Fig. 2a)(Fig. 2a)

(Fig. 2a)

For the exhaust

For the exhaust For the exhaust

For the exhaust hose:

hose: hose:

hose:

Hereupon a flexible exhaust

hose (supplied) with an inner diameter of 150 mm

must be attached. Secure the hose with the cable tie.

• Hang up the hood. Check the secure hold and the

horizontal position. Tighten the lower screws 2x

ST4*30mm through the hood body to secure the

hood

(Fig. 3)

(Fig. 3)(Fig. 3)

(Fig. 3)

For the exhaust hose:

For the exhaust hose: For the exhaust hose:

For the exhaust hose:

Check the correct position of

the exhaust hose and connect it with the outlet open-

ing.

• Fit the telescoping shaft unit. Pull up the inner

shaft and fix the shaft cover to the side of the

bracket using the self-tapping screws 2x

ST4*8mm

(Fig. 4

(Fig. 4(Fig. 4

(Fig. 4)

))

)

Installing the activated carbon

Installing the activated carbonInstalling the activated carbon

Installing the activated carbon

filter for recirculation

filter for recirculation filter for recirculation

filter for recirculation

mode

modemode

mode

• Remove the aluminum grease filter (see “Clean-

ing the aluminum grease filter).

• Place the carbon filter onto the intake of the ex-

haust air duct. Make sure that the fixing pins of

the carbon filter engage in the fastening slots of

the exhaust air duct. Put the filter in A

A A

A and press

firmly flat B

• Reinstall the aluminum grease filter.

Electrical connection

Electrical connectionElectrical connection

Electrical connection

WARNING:

WARNING:WARNING:

WARNING:

• The installation to the mains supply must conform

to the local standards and regulations.

• Improper connection may cause to an electric

electric electric

electric

shock

shockshock

shock!

• Do not modify the appliance plug. If the plug does

not fit properly to the outlet, let install a proper

outlet by an authorized specialist.

• The accessibility of the power plug must be en-

sured to disconnect the appliance from the power

supply in case of emergency.

• Ensure that your mains power corresponds with

the specifications of the appliance. The specifica-

tions are printed on the rating label.

• Connect the mains cable to a properly installed

and earthed wall outlet.

• If the plug after installation is not accessible, a

corresponding disconnect device must be availa-

ble to meet the relevant safety regulations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann DU 7601 G in the language / languages: English, German as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann DU 7601 G Manual

Product: