651971
19
Zoom out
Zoom in
Previous page
1/28
Next page
NOTE
NOTENOTE
NOTE:
::
:
Recomm
RecommRecomm
Recomm
endations for preparation work
endations for preparation workendations for preparation work
endations for preparation work
When installing, ask another
person
Wear protective gloves to prevent injuries from any sharp edges.
1
4
Determine the position of the extractor hood centrally above the hob in conformance with the specified
safety distances.
Mark the necessary holes for the wall mounting
spirit level.
Drill Ø 8 mm mounting holes into
fasten the brackets with the
screws
Attach the suspension rail (1) for the hood body as well as the mounting rail with bracket (2) to the top
edge
parallel to the rail (1) (Fig. A). Determine the extension length of the duct cover in advance!
Before suspending insert the connecting piece with non
above. Make sure that the mounting hooks on the connecting piece latch into place.
For extraction mode:
For extraction mode:For extraction mode:
For extraction mode:
Hereupon the supplied
flexible extraction hose w
B)
and connected to the outside by the extraction outlet.
Hook the extractor hood into the
suspension
Remove the
protective plastic from the telescopic duct.
Fix the outer (lower) duct with
the mounting rail without the bracket (3). The rail is fastened to the holes
provided from the inside of the duct.
19
endations for preparation work
endations for preparation workendations for preparation work
endations for preparation work
person
to assist.
Wear protective gloves to prevent injuries from any sharp edges.
2
5 6
Determine the position of the extractor hood centrally above the hob in conformance with the specified
Mark the necessary holes for the wall mounting
by using the supplied drill template
the wall for the respective brackets (1+2+3).
Insert
screws
(6).
Attach the suspension rail (1) for the hood body as well as the mounting rail with bracket (2) to the top
parallel to the rail (1) (Fig. A). Determine the extension length of the duct cover in advance!
Before suspending insert the connecting piece with non
-
return valves (4) onto the extraction duct from
above. Make sure that the mounting hooks on the connecting piece latch into place.
flexible extraction hose w
ith an inner diameter of Ø 150 mm must be attached
and connected to the outside by the extraction outlet.
suspension
rail (1) (Fig. C). Check that it is se
cure
protective plastic from the telescopic duct.
the mounting rail without the bracket (3). The rail is fastened to the holes
Screw in two plate screws (7
) from the back (Fig.
3
7
Determine the position of the extractor hood centrally above the hob in conformance with the specified
by using the supplied drill template
and check them with a
Insert
the dowel pins (5) and
Attach the suspension rail (1) for the hood body as well as the mounting rail with bracket (2) to the top
parallel to the rail (1) (Fig. A). Determine the extension length of the duct cover in advance!
return valves (4) onto the extraction duct from
above. Make sure that the mounting hooks on the connecting piece latch into place.
ith an inner diameter of Ø 150 mm must be attached
(Fig.
cure
and horizontally level.
the mounting rail without the bracket (3). The rail is fastened to the holes
) from the back (Fig.
D).
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann DU 652 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann DU 652 in the language / languages: English, German as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info