551797
32
Zoom out
Zoom in
Previous page
1/54
Next page
32
Filling up the Water Boiler when using the Device
If there is no more water in the vessel no steam is emitted when
the steam switch (21) is pressed. The water has to be lled up
as follows:
1. Press the on/off switch (4). The red control lamp goes off.
2. Remove the mains plug from the socket!
3. Release the residual pressure with the steam switch (21)
(see “Initial Operation”, points 2 and 3).
WARNING: Danger of Injury!
Please open the safety lock (6) only when no more steam
comes out of the nozzle.
4. Slowly open the safety lock (6) and wait a few seconds
before opening it completely until the overpressure has
been released.
NOTE:
For your protection the safety lock has a release device. If
the pressure in the kettle is still too high, this release device
prevents it from being opened.
5. Fill freshwater from the measuring beaker (15) into the
kettle. Take care of water splashes that might come out
of the boiler. In order to avoid water spray, please use the
funnel supplied (Fig. E). Fill the water in slowly. Do not
overll! Max. water capacity: 1.5 litres.
6. Fasten the safety lock again.
7. Reinsert the plug into the socket and switch on the device
using the on/off switch.
When you have nished using the device
1. Press the on/off switch (4). The red control lamp goes off.
2. Remove the mains plug from the socket!
3. Release the residual pressure with the steam switch (21)
(see “Initial Operation”, points 2 and 3).
4. Allow the device to cool down for approx. 1 hour before you
put it away.
Cleaning and Maintenance
WARNING:
Always remove the mains plug before cleaning the
device.
Under no circumstances should you immerse the device
in water for cleaning purposes. Otherwise this might
result in an electric shock or re.
CAUTION:
Do not use a wire brush or any abrasive items.
Do not use any acidic or abrasive detergents.
Connected Wattage
The station has a total maximum wattage of 1500 W.
CAUTION: overload!
If you use extension leads, these should have a cable
cross-section of at least. 1.5 mm².
Do not use any multiple sockets, as this device is too
powerful.
Using the Device
CAUTION:
Before you begin cleaning you should test the materials to
be cleaned as to their suitability for cleaning with steam. Do
not hold the steam nozzle for too long and too close in one
position.
After you have lled the kettle with water and selected a clean-
ing attachment, please proceed as follows:
1. Turn the lock (22) on the steam pistol (20) to OFF/LOCK
without the steam switch (21) pressed in (Fig. A).
2. Connect the device to a duly installed 230 V/50 Hz protec-
tive contact socket.
3. Press the on/off switch (4) (Fig. F). The red control lamp (3)
lights up. The temperature control lamp (2) shows that the
device is heating up.
4. After approx. 12 min the steam temperature has been
reached and the temperature control lamp (2) goes off. The
device is ready for operation. During use this control lamp
shows that the water is being heated up again.
WARNING:
If the steam switch is pressed while the orange lamp is on, it
is possible for hot water to be ejected from the nozzle.
5. For the purposes of cleaning turn the lock (22) on the
steam pistol (20) to ON (Fig. B1).
6. Point the steam nozzle at the surface to be cleaned and
press the steam switch (21) (Fig. B2).
7. Use the lock (22) to turn the steam pistol to permanent
steam. Keep the steam switch pressed down and turn the
lock to OFF/LOCK at the same time (Fig. C3).
8. In order to release the lock again, please proceed as fol-
lows: hold down the steam switch and turn the lock to ON
at the same time (Fig. D4).
NOTE:
During operation please ensure that the hose does not
become twisted or squashed.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann DR 921 CB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann DR 921 CB in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 9,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info