320246
40
Zoom out
Zoom in
Previous page
1/66
Next page
ENGLISH
ENGLISH
40
Blower Aperture
The device has a blower
function. This enables you to
blow out dust or leaves.
Attach the hose connection
(8) to the blower aperture
(12).
Mains Lead
To use the device please unwind the entire lead.
After use you can wind up the lead in the cable duct on the
motor housing.
Parking Position
On the motor housing your
device has a holder for the
oor nozzle.
Here you can hang up the
nozzle in order to “park” it.
Operation
General
Select the desired accessory.
Unwind the lead completely.
Insert the mains plug into a correctly installed 230 V, 50 Hz
power socket.
Dry Vacuuming
Insert the permanent dust bag; it may be necessary before-
hand to remove the hose connection.
Attach the motor housing.
Assemble the accessory.
Turn the device on.
Vacuum at a steady speed. There is no need to exert
pressure.
Removing and Emptying the Dust Bag
Turn the device off with the on/off switch (2). Pull the plug
out of the socket.
Remove the motor housing.
Take off the hose connection.
Remove the dust bag.
Empty the dust bag by pulling off the clip.
Push the clip back in place and reinsert the bag. Check that
it is inserted properly in the holder.
Reassemble the hose connection and the motor housing.
Now you can use the device again.
Wet Vacuuming
CAUTION:
Never use the dust bag when vacuuming up liquids.
Allow the hose connection to discharge directly into the
collection vessel.
Do not use the fl oor nozzle, but the parquet brush.
Before the cleaner is used again for dry vacuuming, all
components must be dry.
Remove the permanent dust bag and reattach the motor
housing.
Assemble the attachment.
Switch the device on.
CAUTION:
Turn the device off immediately if foam forms, liquid leaks out
or if the vessel is full.
ޥ NOTE:
When the vessel is full the fl oat valve (16) closes the suction
aperture and the motor runs at a higher speed. Switch the
device off immediately and empty it.
Emptying the Collection Vessel
Turn the device off by the on/off switch (2). Pull the plug out
of the socket.
Remove the motor housing.
Empty the collection vessel.
Reassemble the hose connection and the motor housing.
You can now use the vacuum cleaner again.
Cleaning and storage
Pull the plug out of the socket.
In order not to damage the surfaces, please do not use any
abrasive detergents or scratching cleaning utensils.
Collection Vessel
Rinse out the collection vessel after use with clean water.
Any dirt in the vessel can be removed with a sponge or
nylon brush.
Permanent Dust Bag
Quick cleaning: Tap or brush out the dust bag in order to
remove any residues.
Hand wash: If soiling is more severe we recommend a
hand wash up to 40°C.
ޥ NOTE:
The bag should only be allowed to dry in the air!
Only use the vacuum cleaner again when the dust bag is
dry!
05-BS 981 CB 40 26.09.2006, 10:22:44 Uhr
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann bs 981 cb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann bs 981 cb in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info