Manual Bomann BS 9027 CB (page 33 of 58) (English, German, Dutch, French, Italian, Polish, Spanish)

651937

Zoom out

Zoom in

1/58

BS9027CB_IM 08.03.16

Switching off and Winding up the Mains Lead

1. Turn the vacuum cleaner off by the on / off switch and

remove the plug from the socket.

2. Hold the cable to avoid wrapping.

3. Press the cable winding button and guide the cable.

Maintenance

Emptying the dust collector

Empty the dust collector once the collected dirt reaches the

MAX marking.

1. Disconnect the mains plug from the wall socket.

2. Press the button (7) to release the dust collector. Remove

the dust collector.

3. Empty the dust collector over a dustbin. In order to do so,

press the button on the dust collector to open the base

plate. (Page 4, Fig. B)

4. Then close the base plate again.

5. Attach the dust collector to the appliance. First position it

at the bottom of the appliance and then secure it with the

hook on top.

6. Check that the position of the dust collector is secure by

briey lifting the appliance at its carrying handle.

The Filter System

Your appliance features 4 lters. The common dust bag

system has been replaced by a transparent dust collector.

The higher ow speed of the collector allows for heavy dirt

and smallest oating particles to be separated from the

“sucked-in air”.

It is thus not necessary to buy dust bags.

The lters must be cleaned periodically.

The lter unit (Page 4, Fig. C to H)

The lter unit is composed of:

• Nylon lter

• Filter eece

• Central lter

• Pre-lter

• Fastening disk

CAUTION:

• Never wash the components in a washing machine or a

dishwasher!

• Do not use a hairdryer for drying.

• Operate the appliance again only when all components

are completely dry and have been installed correctly.

Proceed as follows to clean the lter unit:

1. Empty the dust container as described above. (Steps

1 - 3)

2. Disassembly of the lter unit

2.1. Turn the lter unit in the

direction. (Fig. C)

2.2. Pull the lter unit from the dust container. (Fig. D)

2.3. Turn the fastening disk and pull it off. (Fig. E)

2.4. Pull the pre-lter from the central lter. (Fig. F)

2.5. Open the cover of the lter unit. (Fig. G)

2.6. Remove the nylon lter and the lter eece. (Fig. H)

3. Clean all parts of the lter unit and the dust container

under running water. You may use a soft brush.

4. Allow all parts to dry completely in air.

5. Assembly of the lter unit

5.1. Insert the lter eece and then the nylon lter into

the cover.

5.2. Close the cover. It must lock mechanically.

5.3. Set the pre-lter to the central lter.

NOTE:

The pre-lter has recesses of different sizes,

which match the tabs on the central lter.

5.4. Set the fastening disk onto the pre-lter and tighten

it by turning.

5.5. Replace the lter unit in the dust container: Set

the guide tab on the lter unit to the

symbol.

Tighten the lter unit by turning it in the direction.

Outlet lter

The appliance is also equipped with an outlet lter.

It is located on the back of the appliance.

1. Push the lock (10) down and remove the ventilation grill.

2. Remove the lter insert and clean it as described above.

3. Place the completely dry lter back into the ventilation

grille.

4. Put the ventilation grille back on the appliance. Observe

the guide lugs. The ventilation grid must engage audibly.

Cleaning

WARNING:

• Before cleaning remove the mains lead from the socket.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann BS 9027 CB in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann BS 9027 CB Manual

Product: