Manual Bomann AE 1918 (page 32 of 58) (English, German, Dutch, French, Italian, Polish, Spanish)

687951

Zoom out

Zoom in

1/58

AE1918CB_Instruction Manual 26.10.16

Unpacking the appliance

1. Remove the appliance from its packaging.

2. Remove all packaging materials like foils, lling materials,

cable holders, and carton packaging.

3. Check the scope of deliveries for completeness.

NOTE:

There may still be dust or production remains on the

appliance.

We recommend that you clean the appliance as described

under “Cleaning”.

NOTE:

Remove the cardboard disk insert from the inside of the

lter / blade unit (4) before starting the motor.

Description of the Parts

1 Pusher

2 Chute

3 Lid

4 Filter / Blade

5 Receptacle

6 Fold up spout

7 Drive wheel (not detachable)

8 Locking bar with safety switch

9 Base with motor

10 On / off speed control (I / 0 / II)

11 Pulp collector

Setting up of the appliance

For assembly, also refer to the illustrations on page 3.

1. Set the appliance so that the speed controls (10) point

towards you.

2. Tilt the locking bar (8) to the right.

3. Attach the receptacle (5) on top of the base casing. The

base casing (9) has a recess. Here the spout (6) of the

receptacle casing (5) must be placed.

WARNING risk of cuts!

The lter / blade (4) is sharp!

4. Place the lter / blade (4) on top of the drive wheel. Press

it down. It clicks in place on the drive wheel.

5. Check the lter / blade (4)! Feel under the lter edge. It

should not loosen under slight tension.

6. Attach the pulp collector (11) on the left side. To do so,

hold it slightly sideways to press the upper edge into the

shroud of the receptacle casing (5).

7. Attach the lid (3). It reaches all the way over the pulp

collector (11).

NOTE:

Your appliance is equipped with a safety switch. It

prevents accidental motor start. Check the correct

locking of the locking bar (8).

8. Lock the locking bar (8) over the lid (3).

9. Press the spout (6) downwards to open the ow of the juice.

10. Place the juice jug to the right of the appliance.

11. Ensure that the speed control (10) is set to “0” position.

Electric Connection

• Before inserting the power plug into the outlet, check

that the mains voltage to be used matches that of the

appliance. You can nd the required information on the

nameplate.

• Connect the appliance only to a correctly installed safety

socket.

Operation

Speed control settings

• Select setting “I” for smaller fruit like strawberries.

• Select setting “II” for larger pieces or hard vegetables, for

example carrots.

Preparations

• Wash the fruit to be processed.

• Cut the fruit in pieces to t through the chute opening (2).

• Remove large pips and stems.

Extracting Juice

NOTE:

The appliance is intended for short-term use. After opera-

ting it for 6 minutes, take a 5 minute break.

WARNING:

• Check all accessories again for proper attachment before

switching the appliance on.

• Ensure that the spout is pressed downwards.

NOTE:

Remove the cardboard disk insert from the inside of the

lter / blade unit (4) before starting the motor.

1. Set the speed control (10) to the desired position. The

motor starts running.

2. Insert the fruit pieces in the chute opening (2) and push

them down with the pusher (1). Please note! The pusher

(1) has a guide way in the ller opening.

3. The juice ows out at the right side of the casing. The pulp

is collected in the pulp collector (11). If there is an exces-

sive discharge of juice, switch the speed control (10) to

setting “I” and exert less pressure on the pusher (1).

NOTE:

• Observe the juice jug. Stop operation in time to prevent

overowing.

• Berries and citrus fruits (such as gooseberries, grapes,

oranges) are usually not juiced but pressed.

• When juicing these fruits with their high juice content,

splashing of juice from the area of the pulp collector (11)

may occur. In this case, we recommend that the pulp

collector (11) is emptied more frequently.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann AE 1918 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann AE 1918 Manual

Product: