573537

BodySculpture BE-5940 Manual

11
Zoom out
Zoom in
Previous page
1/14
Next page
9
EXERCISE COMPUTER
FUNCTION BUTTON
MODE PRESS TO SELECT FUNCTION DISPLAY, AND HOLD ON PRESSING FOR 4 SECONDS TO
HAVE ALL FUNCTION VALUES TOTAL RESET.
(THERE IS NO SINGLE FUNCTION RESET AVAILABLE.)
FUNCTIONS
SCAN AUTOMATICALLY SCANS THROUGH EACH FUNCTION EVERY 6 SECONDS.
TIME DISPLAYS THE ACCUMULATED TIME UP TO 99:59 DURING EXERCISING.
SPEED DISPLAYS THE CURRENT SPEED UP TO 999.9KM/H OR ML/H, THE VALUE WILL STAY ON
THE MONITOR CONSTANTLY.
DISTANCE DISPLAYS THE ACCUMULATED DISTANCE UP TO 99.99 KM OR ML DURING
EXERCISING.
RPM DISPLAYS CURRENT ROTATION PER MINUTE.
CALORIES DISPLAYS THE ACCUMULATED CALORIE CONSUPMTION UP TO 999.9 CAL DURING
EXERCISING.
(THIS DATA IS A ROUGH GUIDE FOR COMPARISON OF DIFFERENT SESSIONS
EXERCISING SESSIONS THAT CAN NOT BE USED FOR MEDICAL TREATMENT.)
PULSE THE MONITOR WILL SHOW YOUR CURRENT HEART RATE FIGURE IN A FEW SECONDS
AFTER YOU HOLD TWO HANDGRIP SENSORS. TO ENSURE THE PULSE READOUT
MORE PRECISE, PLEASE DO HOLD TWO HANDS TOGETHER DURING TRAINING
PERIOD
N
N
O
O
T
T
E
E
1. WHEN STOP EXERCISING, THERE WILL BE A STOP SIGN SHOWN ON THE UPPER-LEFT CORNER.
2. WITH NO SIGNAL TRANSMITTED INTO THE MONITOR IN A PERIOD OF 4 MINUTES, THE LCD DISPLAY
WILL SHUT OFF AUTOMATICALLY, AND ALL FUNCTION VALUES WILL BE STORED
3. TURN ON THE MONITOR BY PRESSING THE BUTTON OR START EXERCISING, ALL FUNCTION
VALUES(SPEED EXCLUDED) WILL START COUNTING FROM PREVIOUS DATAS.
4. IF IMPROPER DISPLAY ON MONITOR, PLS RE-INSTALL THE BATTERIES TO HAVE A GOOD RESULT.
5.
WARNING! Heart rate monitoring systems may be inaccurate. Over exercise may result in
serious injury or death. If you feel faint stop exercising immediately”
TROUBLE SHOOTING.
1. Change the battery. To change the computer battery, please slide the computer from the computer holder,
remove the battery cover on the back of the computer console, and remove the batteries. Replace with 1 x AA
batteries. Finally put the cover back on the console, and slide the computer back on the computer holder.
2. Computer not working correctly
. If your computer is not working correctly, please check whether the lower
sensor wire is connected to the upper sensor wire, and make sure the upper sensor wire is plugged into the
computer. When you have checked the above, and the computer still not working, then please make sure the
batteries are installed correctly in the computer and that the batteries are still working.
3. No resistance.
If there is no tension resistance on the bike, please make sure the upper tension cable is
connected to the lower tension cable. Turn the tension knob anti-clockwise to it’s lowest level, then go to the
tension strap buckle which is situated on top of the flywheel cover at the base of the front post. Loosen the
tension strap, pull it through the buckle until you can feel some resistance on the strap then lock it back around
the buckle. Now mount the cycle and turn the pedals, the tension control knob can now be used for a finer
adjustment. If you find it is now too tight go back to the tension strap buckle and loosen the strap slightly.
M
M
A
A
I
I
N
N
T
T
E
E
N
N
A
A
N
N
C
C
E
E
1. Before using the bike, always make sure all bolts/nuts are fully tightened.
2. A spent battery is hazardous waste, please dispose of it correctly, and do not throw it in the trash.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BodySculpture BE-5940 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BodySculpture BE-5940 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info