518693

BodyCraft Xpress Pro Manual

8
Zoom out
Zoom in
Previous page
1/13
Next page
28
87
45
97
23
4
97
16
88
99
99
55
88
44
17
93
93
23
75
66
45
12
11
33
92
99
28
1
7
95
95
101
102
101
101
104
102
66
104
101
107
115
107
101
116
101
101
113
107
12L
45A
75A
45A
75A
45A
45A
75A
45A
75A
45A
12R
116
102
102
95
95
102
102
77
76
75
19
45
45
110
45
116
45
116
110
116
116
ST E P 3 A SSE M B L E SE A T F R A M E A ND SE A T B A C K
7
1. Attach Seat Frame(11) to Front Upright(4) using two 3/8"X3" Bolts(88), four 3/8" Washers(101) and two
3/8" Nuts(107). Attach Seat Frame(11) to Base Frame(1) using 3/8"X4-1/2" Bolt(87), two 3/8"
Washers(101) and one 3/8" Nut(107).
2. Attach Leg Extension Arm with bearing pre-installed(12) to Seat Frame(11) by aligning holes and then
inserting Leg Extension Axle(33). Fasten Leg Extension Axle(33) using two 5/16" Spring Washers(104),
two 5/16" Washers(102) and two 5/16"X5/8" Set Screws(97). Check to ensure that Leg Extension
Arm(12) pivots freely. Attach the Right and Left Leg Extension Arms(12R & 12L) to the Leg Extension
Arm(12) by 5/16"X1/2" Set Screw(113). Moisten the center of two Cover of Foam Pads(75A) and slide
onto each end of the Right and Left Leg Extension Arms(12R & 12L). Attach Plastic Washer (45A) at
both side of Cover of Foam Pad(75A) and secure the pads with 5/16"x32mm Sunken Head Screw(116).
Note: The L Pin(55) is used to lock the Leg Extension Arm(12) into place when using the low 
cable for exercises such as arm curls, leg kicks, upright rows, etc. Remove the L Pin(55) when 
performing leg extensions and leg curls.
3. Insert Foam Roller Bar(23) into hole in Chromed Seat Adjuster(16). Moisten Foam Pad(75) with water
and slide onto each end of Foam Rollers Bar(23). Attach Plastic Washer(45A) to both side of Cover of
Foam Pad(75A) and secure the Pads with 5/16"X32mm Sunken Head Screw(116).
4. Attach Seat Pad(77) to Chromed Seat Adjuster(16) using two 3/8" Washers(101) and two 3/8"X1-3/4"
Bolts(92). Attach 25X50mm Plug(44) to Chromed Seat Adjuster(16) and 50mm SQ. Plug(41) to Seat
Frame(11). Insert Chromed Seat Adjuster(16) into Seat Frame(11) and lock into place with Pop Pin(53)
with Spring(115).
5. Attach Seat Back Adjuster(17) to Front Upright(4) using one 3/8"X3" Bolt(88) and 3/8" Nut(107). It may
be necessary to tighten this bolt, then lossen just enough to let Seat Back Adjuster(17) pivot freely.
Attach Pop Pin(53) for Seat Back Adjuster(17) to Front Upright(4). Attach two Metal Hinges(19) to top
of Seat Back Adjuster(17), then attach Back Pad(76) to Metal Hinges(19) using two 3/8"X1-3/4"
Bolts(93) and two 3/8" Washers(101). Insert Foam Roller Bar(23) into hole in Seat Back Adjuster(17).
Moisten two Foam Pads(75) with water and slide onto each end of Foam Roller(23), then attach Plastic
Washer(45A) at both side of Cover of Foam Pads(75A) and secure pads with 5/16"x32mm Sunken
Head Screw(116). Lock into place with pre-installed Set Screw.
6. Attach Weight Shroud(28) to Base Frame(1) and Top Guide Rod Retainer(7) using four 5/16"X1/2"
Bolts(95) and four 5/16" Washers(102).
Tighten all the bolts and nuts gradually.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BodyCraft Xpress Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BodyCraft Xpress Pro in the language / languages: English as an attachment in your email.

The manual is 4,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info