518710

BodyCraft Xpress Pro Legpress Manual

6
Zoom out
Zoom in
Previous page
1/10
Next page
1. Attach the Leg Press Main Frame (202) to the Weight Base Connector (207) and
the Long Leg Press Connector (205) using four 3/8" X 4" Hex Bolts (229), eight
3/8" Washers (238) and four 3/8" Nylon Nuts (241).
2. Attach the Base Stabilizer (201) to the Leg Press Main Frame (202) using two
1/2" X 3-1/4" Hex Bolts (227), four 1/2" Washers (237) and two 1/2" Nylon Nuts
(240). Attach a 45mm X 75mm Rect. Cap (214) to the bottom rear of the Leg
Press Main Frame (202). Attach a 50 mm Sq. Caps (215) to each end of the
Base Stabilizer (201).
3. Slide a Bearing Housing (212) onto each end of the welded axle on the Rear Leg
Press Support (208) and then bolt the Bearing Housings (212) to the Leg Press
Main Frame (202) using four 1/2¨ X 1-3/4¨ Hex Bolts (228), eight 1/2¨ Washers
(237) and two 1/2¨ Nuts (240).
4. Attach the Front Leg Press Support (206) to the Leg Press Main Frame (202)
using one 5/8" X 6-1/2" Hex Bolt (226), two 5/8" Washers (236) and one 5/8"
Nylon Nut (239).
5. Attach the Foot Plate Connector (209) to the Rear Leg Press Support (208) and
the Front Leg Press Support (206) using one 5/8" X 6-1/2" Hex Bolt (226), two
5/8" Washers (236) and one 5/8" Nylon Nut in each Leg Press Support.
6. Attach the Foot Plate (210) to the Foot Plate Connector (209) using two 1/2"
Washers (237) and two 1/2" Nylon Nuts (240). Attach two 45mm X 75mm Rect.
Plugs (216) to the Foot Plate (210).
7. Attach the Right and Left Leg Press Handles (203 & 204) to the Leg Press Main
Frame (202), angle facing up, using two 3/8" X 3-1/8" Hex Bolts (230), four 3/8"
Washers (238) and two 3/8" Nylon Nuts (241).
8. Attach the Seat Pad for Leg Press (225) to the Leg Press Main Frame (202) using
two 3/8" X 1" Hex Bolts (234), one 3/8" X 2-3/4" Hex Bolt (231) and three 3/8"
Washers (238). Attach the Back Pad for Leg Press (224) to the Back Pad
Adjuster (211) using two 3/8" Washers (238) and two 3/8" X 1" Hex Bolts (234).
Screw the Locking Spring Knob (220) into the Leg Press Main Frame (202) and
the slide the Back Pad Adjuster (211) into the Main Frame. Adjust to the desired
position by pulling the Locking Spring Knob (220).
Tighten all bolts gradually, from ground - up.
STEP 2
-5-
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BodyCraft Xpress Pro Legpress at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BodyCraft Xpress Pro Legpress in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info