HOW TO REMOVE YOUR CHILD SEAT FROM A LUGAGGE CARRIER
ASSEMBLY INSTRUCTIONS
EXCLUSIVE MAXI & TOUR PLUS FRAME
HOW TO ASSEMBLE YOUR CHILD SEAT ON A BICYCLE FRAME
1. Open the buckle(C1) and detach the safety-belt (C) in order to remove the child bicycle seat.
2. Press the jaws (I) and pull both of them out. At the same time, pull the child seat up and back.
1. Access the front cover of the child seat (E) and remove the key (N).
2. Remove the metallic bracket (K) from the metallic support bar (L). To do
that, you should press the metallic bracket button (K3) and simultaneously
pull the metallic support bar (L) up.
3. Remove the screws (K1) on the Metallic bracket (K), with the Allen key
No. 5 (N).
4. The correct positioning of the metallic bracket (K) is extremely
important. Make sure the metallic bracket (K) is positioned in the frame
according to the picture. Place the body of the front mounting block (K2)
on the bicycle frame from the front. Insert 4 screws (K1) in the block to
tighten the rear metallic mounting plate (K4), so that the hight can be
adjusted later.
5. Tighten the screws, with the Key (N), so that the metalic bracket (K) is
secured but not fully tightened so that, if necessary, you can adjust the
height later. However, note that it should be tight to make it easier to
complete the next step. You need to tighten the 4 screws diagonally and
in stages. Check the safety of the fasteners regularly.
6. Place the edges of the metallic support bar (L) at the holes of the metallic
bracket (K) until you hear a click indicating the lock, and until the centre
button (K3) shall be level with the exterior of the hose metallic bracket.
7. Centre and adjust the metallic bracket (K) at a height above the rear
wheel, so that later, when you add the weight of the child, the child bicycle
seat does not touch the wheel. Note that the metallic bracket (K) should
be positioned at a maximum of 10cm away from the wheel. Never use
the metallic support bar (L) to carry other loads than this child seat, as
indicated in this manual.
8. To install the metallic support bar (L) on the child seat (A) you need to
first clamp the frontal clamping point (L1) on the Safety Metallic Device (J).
9. Then, clip the Metallic support bar lateral clamping points (L2) on the
opening and clamping jaw (I) of the child seat (A). Make sure that you will
hear a click when the clamping is done, this is extremely important for you
and your child safety.
10. The child seat has a center of gravity (F) (engraved on the child seat)
that must be positioned in front of the rear wheel axle. If it is positioned
behind the axle, the distance must not exceed 10 cm. Special care must
also be taken when positioning the child seat to ensure that the cyclist
does not touch the child seat with his feet when cycling.
Note: In Germany, according to the German Traffic Law StVZO, bicycle seats
may only be fixed so that 2/3 of the seat depth or the Gravity Center of the
seat is located between the front and rear axle of the bicycle.
11. After adjusting the height and positioning of the seat, hand tighten the
Metallic bracket (K) to ensure that it cannot move. This tightening must
be manual and is extremely important for the safety of the child. Make
sure that the Metallic bracket (K) is firmly attached. You need to hand tight
the 4 screws (K1) diagonally, with the same force and in stages, with a
recomended torque of 8 N.m.
12. Start to open the safety belt buckle (C1) and pass it around the bicycle
frame. Adjust the belt it as shown in the picture, under tension.
13. Make sure that remain loosen belt is not in contact with the wheel,
so pass it trought the Safety belt retainer (C2). This step is extremely
important for the child’s safety.
14. Make sure you have followed and fulfilled all the instructions given.
When done so, the child bicycle seat is ready for use. IT IS MANDATORY
TO READ the following chapter on safety instructions about using
your child bicycle seat.
1. Open the buckle (C1) and detach the safety-belt (C) in order to remove the child bicycle seat.
2. If you want to remove the full system, press the block button (K3) of the Metallic Bracket (K) and simultaneously pull the metallic Support bar (L) and
the seat up and back as shown in the image.
3. If you wish to keep the metallic support bar (L) and only remove the seat, press the jaws (I) and pull both of them out. At the same time, pull the child
seat up and back.
ASSEMBLY INSTRUCTIONS
EXCLUSIVE MAXI & TOUR PLUS FRAME
HOW TO REMOVE YOUR CHILD SEAT FROM A BICYCLE FRAME
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bobike Exclusive Tour Plus at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bobike Exclusive Tour Plus in the language / languages: All languages as an attachment in your email.
The manual is 5.93 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
