732396
5
Zoom out
Zoom in
Previous page
1/6
Next page
4
Left joystick
Climb
Descend
Turn
left
Turn
right
Step back
Step left
Right joystick
Backward
Forward
Move
left
Move
right
Step forward
Step right
SPECIAL FEATURES
Obstacle sensor
When the sensor detects an obstacle at a distance of 1 meter (depending on the envi-
ronment), the drone stops moving. The sensor is activated automatically 1 metre above
the ground. The sensor cannot prevent all crashes, so never fly too close to people and
animals.
1m
1m
1m 1m
CAUTION: Obstacle detection only works at low speeds and in good visibility. The sensor
cannot detect glass surfaces. Best results are achieved when detecting white walls. When
sensor is working, it is not possible to use headless mode or the return to starting point
button.
Maintaining height
When releasing the height control joystick, the drone remains hovering at the same height.
Flip
Climb to a height of at least 2 metres and press and hold the left joystick. Then move the
right joystick in any direction and the drone will flip up and over in that direction and back.
CAUTION: Flip does not work when the obstacle sensor is attached to the drone. After
removing it, you must restart the controller. Flip also does not function when the battery
is low.
Speed switch
By pressing the right joystick, you can choose between slow (one beep), medium (two
beeps), and high (three beeps) speed.
Return to start point
Press the button and the drone will fly back to its starting position. With the right joys-
tick, you can control the flight back to the left or right. Move the right joystick up to abort.
Only use the return function in the open air and when the air is calm. It cannot be guaran-
teed that this feature will return the drone to the exact same position as it depends on the
surrounding conditions. Therefore, when flying, keep the drone under control and under
supervision so you can safely land it. Using the return function does not exclude you from
damage or injury liability.
Headless mode
Turning on
After pairing the drone with the controller, press the headless mode button. The controller
beeps and the LEDs on the drone blink.
Turning off
When the drone is in headless mode, press the headless mode button. The controller then
beeps and the LEDs light up.
Setting forward direction
Before turning on headless mode, you
need to set the direction forward. Point the
drone so that it is facing the same direc-
tion as you (1). Then move both joysticks
to the left and hold them in this position
for 2 seconds (2). The LEDs on the drone
will flash.
Controls in headless mode
In headless mode, the forward direction is
always the direction that has been pre-set.
Always stand facing this direction during
operation. In headless mode, it does not
matter which direction you turn the drone
– when moving the right joystick forward,
it always flies away from you, even if it is
facing sideways.
1 2
TIPS:
1. The simplest way to fly in headless mode is to carefully set the forward direction and
after take-off to make sure you stand facing this direction and not to move.
2. If the drone moves differently than it should, abort the flight and set it up again.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BML Phoenix at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BML Phoenix in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info