230064
4
Zoom out
Zoom in
Previous page
1/6
Next page
PAGE 4 / 6
To initiate pairing:
1. Place the BLUETREK® X2 and your mobile phone within 0.3 meter (1 foot) from
each other.
2. Switch on your phone and select its Bluetooth® discover mode (refer to the
Bluetooth® mobile phone user manual).
3. When the BLUETREK® X2 is switched off, press and hold the TALK button for
about 7 seconds until the indicator light flashes red and blue alternately. And a
sound can be heard in the speaker.
4. Once the mobile phone detects the headset, a “BLUETREK X2” message will be
displayed. Follow the phone instructions to accept the pairing. The PIN code (or
passkey) is 0000, then press “yes” or “ok”.
If pairing success, the indicator light will switch to blue and flashes slowly.
If you haven’t started the discovery mode within 5 minutes, the headset will switch off.
You must then switch on your headset and start the pairing again.
Wearing the BLUETREK® X2
For your convenience, the ear loops and the ear hook of BLUETREK® X2 are designed
to be removable and can be worn on either ear. BLUETREK®X2, as packaged, is
already with the small ear loop that is specially designed for active outdoor use.
To replace with the ear hook:
Simply unsnap the ear loop from the headset by pulling gently at the base of the ear
clamp ring.
Snap the ear hook onto the headset by applying gentle pressure on the base of the ear
clamp ring.
The ear hook is made of a soft material which can be shaped to fit your ear. Please refer
to the above diagram of how it can be adjusted.
Switching the BLUETREK® X2 ON and OFF
Switching BLUETREK® X2 ON
When your headset is off, press and hold the TALK button for about 2 seconds until the
blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the
TALK Button.
To check if your headset is ON, press once on the TALK button. If the indicator light
flashes blue, it means your headset is ON.
Switching BLUETREK® X2 OFF
When your headset is on, press and hold the TALK button for about 5 seconds until the
red indicator light is on after the quick blue flashes. A beep (2 tones) can be heard in the
speaker then release the TALK Button.
Making a call
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bluetrek x2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bluetrek x2 in the language / languages: English as an attachment in your email.

The manual is 0,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info