582057

Blomberg WNF 8543 AE20 Manual

3
Zoom out
Zoom in
Previous page
1/51
Next page
3 - EN
2 Installation
RefertothenearestAuthorisedServiceAgentfor
installation of the product. To make the product
ready for use, review the information in the
user manual and make sure that the electricity,
tap water supply and water drainage systems
areappropriatebeforecallingtheAuthorized
ServiceAgent.Iftheyarenot,callaqualified
technicianandplumbertohaveanynecessary
arrangements carried out.
C
Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer's
responsibility.
B
Installationandelectricalconnectionsof
theproductmustbecarriedoutbythe
AuthorizedServiceAgent.Manufacturershall
notbeheldliablefordamagesthatmayarise
fromprocedurescarriedoutbyunauthorized
persons.
A
Prior to installation, visually check if the
producthasanydefectsonit.Ifso,donot
haveitinstalled.Damagedproductscause
risks for your safety.
C
Makesurethatthewaterinletanddischarge
hosesaswellasthepowercablearenot
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
Appropriate installation location
• Placethemachineonarigidfloor.Donot
place it on a long pile rug or similar surfaces.
• Totalweightofthewashingmachineandthe
dryer-withfullload-whentheyareplaced
on top of each other reaches to approx.
180kilograms.Placetheproductonasolid
and flat floor that has sufficient load carrying
capacity!
• Donotplacetheproductonthepower
cable.
• Donotinstalltheproductatplaceswhere
temperaturemayfallbelow0ºC.
• Placetheproductatleast1cmawayfrom
the edges of other furniture.
Removing packaging reinforcement
Tiltthemachinebackwardstoremovethe
packaging reinforcement. Remove the packaging
reinforcementbypullingtheribbon.
Removing the transportation locks
A
Donotremovethetransportation
locksbeforetakingoutthepackaging
reinforcement.
A
Removethetransportationsafetybolts
beforeoperatingthewashingmachine,
otherwise,theproductwillbedamaged.
1. Loosenalltheboltswithaspanneruntilthey
rotatefreely(C).
2. Removetransportationsafetyboltsby
turning them gently.
3. Attachtheplasticcoverssuppliedinthe
UserManualbagintotheholesontherear
panel. (P)
C
Keepthetransportationsafetyboltsinasafe
place to reuse when the washing machine
needstobemovedagaininthefuture.
C
Nevermovetheproductwithoutthe
transportationsafetyboltsproperlyfixedin
place!
Connecting water supply
C
Thewatersupplypressurerequiredtorun
theproductisbetween1to10bars(0.1
–10MPa).Itisnecessarytohave10–80
liters of water flowing from the fully open
tap in one minute to have your machine run
smoothly.Attachapressurereducingvalveif
water pressure is higher.
C
Ifyouaregoingtousethedoublewater-inlet
productasasingle(cold)water-inletunit,
you must install the supplied stopper to the
hotwatervalvebeforeoperatingtheproduct.
(Appliesfortheproductssuppliedwitha
blindstoppergroup.)
C
Ifyouwanttousebothwaterinletsofthe
product, connect the hot water hose after
removing the stopper and gasket group from
thehotwatervalve.(Appliesfortheproducts
suppliedwithablindstoppergroup.)
A
Modelswithasinglewaterinletshouldnot
beconnectedtothehotwatertap.Insuch
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
A
Donotuseoldorusedwaterinlethoses
onthenewproduct.Itmaycausestainson
your laundry.
1. Connectthespecialhosessuppliedwiththe
product to the water inlets on the product.
Redhose(left)(max.90ºC)isforhotwater
inlet,bluehose(right)(max.25ºC)isforcold
water inlet.
A
Ensurethatthecoldandhotwater
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end of the
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg WNF 8543 AE20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg WNF 8543 AE20 in the language / languages: English as an attachment in your email.

The manual is 5,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info