581987

Blomberg WNF 8427 ACE 40 Manual

3
Zoom out
Zoom in
Previous page
1/71
Next page
3
EN
Appropriate installation location
• Placethemachineonarigidfloor.Donot
place it on a long pile rug or similar surfaces.
• Totalweightofthewashingmachineandthe
dryer-withfullload-whentheyareplaced
on top of each other reaches to approx. 180
kilograms. Place the product on a solid and flat
floor that has sufficient load carrying capacity!
• Donotplacetheproductonthepowercable.
• Donotinstalltheproductatplaceswhere
temperaturemayfallbelow0ºC.
• Placetheproductatleast1cmawayfromthe
edges of other furniture.
Removing packaging reinforcement
Tiltthemachinebackwardstoremovethe
packaging reinforcement. Remove the packaging
reinforcementbypullingtheribbon.
Removing the transportation locks
A
Donotremovethetransportationlocksbefore
taking out the packaging reinforcement.
A
Removethetransportationsafetyboltsbefore
operating the washing machine, otherwise, the
productwillbedamaged.
1. Loosenalltheboltswithaspanneruntilthey
rotate freely (C).
2. Removetransportationsafetyboltsbyturning
them gently.
3. AttachtheplasticcoverssuppliedintheUser
Manualbagintotheholesontherearpanel.
(P)
C
Keepthetransportationsafetyboltsinasafe
place to reuse when the washing machine
needstobemovedagaininthefuture.
C
Never move the product without the
transportationsafetyboltsproperlyfixedin
place!
Connecting water supply
C
Thewatersupplypressurerequiredtorun
theproductisbetween1to10bars(0.1–10
MPa).Itisnecessarytohave10–80litersof
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
C
Ifyouaregoingtousethedoublewater-inlet
productasasingle(cold)water-inletunit,you
must install the supplied stopper to the hot
watervalvebeforeoperatingtheproduct.
(Appliesfortheproductssuppliedwithablind
stopper group.)
C
Ifyouwanttousebothwaterinletsofthe
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
suppliedwithablindstoppergroup.)
A
Modelswithasinglewaterinletshouldnotbe
connectedtothehotwatertap.Insuchacase
the laundry will get damaged or the product
will switch to protection mode and will not
operate.
A
Donotuseoldorusedwaterinlethoseson
thenewproduct.Itmaycausestainsonyour
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose(left)(max.90ºC)isforhotwaterinlet,
bluehose(right)(max.25ºC)isforcoldwater
inlet.
A
Ensure that the cold and hot water
connections are made correctly when installing
theproduct.Otherwise,yourlaundrywillcome
out hot at the end of the washing process and
wear out.
2. Tightenallhosenutsbyhand.Neverusea
wrench when tightening the nuts.
3. Openthetapscompletelyaftermakingthe
hose connection to check for water leaks at
theconnectionpoints.Ifanyleaksoccur,turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
waterleakagesanddamagescausedbythem,
keep the taps closed when the machine is not
in use.
Connecting to the drain
• Theendofthedrainhosemustbedirectly
connected to the wastewater drain or to the
washbasin.
A
Yourhousewillbefloodedifthehosecomes
out of its housing during water discharge.
Moreover, there is risk of scalding due to
high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of
the discharge hose tightly so that it cannot
come out.
• Thehoseshouldbeattachedtoaheightofat
least 40 cm, and 100 cm at most.
• Incasethehoseiselevatedafterlayingiton
the floor level or close to the ground (less than
40cmabovetheground),waterdischarge
becomesmoredifficultandthelaundrymay
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg WNF 8427 ACE 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg WNF 8427 ACE 40 in the language / languages: English, Danish as an attachment in your email.

The manual is 3,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info