Manual Blomberg WNF 7300 WE20 (page 12 of 68) (English, German, Italian)

582068

Zoom out

Zoom in

1/68

active, previously selected programme will continue

running.

ToactivatetheChildLock:

Pressandhold1

and 2

Auxiliary Function buttons for

3seconds.Thelightsonthe1

and 2

Auxiliary Function

buttonswillflash,and"C03","C02","C01"willappearonthe

display respectively while you keep the buttons pressed for

3 seconds. Then, "Con" will appear on the display indicating

thattheChildLockisactivated.Ifyoupressanybuttonorturn

theProgrammeSelectionknobwhentheChildLockisactive,

samephrasewillappearonthedisplay.Thelightsonthe1st

and 2nd auxiliary function buttons that are used to deactivate

theChildLockwillblink3times.

TodeactivatetheChildLock:

Pressandhold1

and 2

auxiliary function buttons for 3

seconds while any programme is running. The lights on the

and 2

AuxiliaryFunctionbuttonswillflash,and"C03",

"C02","C01"willappearonthedisplayrespectivelywhile

you keep the buttons pressed for 3 seconds. Then, "COFF"

willappearonthedisplayindicatingthattheChildLockis

deactivated.

 Inadditiontothemethodabove,todeactivatetheChild

Lock,switchtheProgrammeSelectionknobtoOn/

Off position when no programme is running, and select

another programme.

 ChildLockisnotdeactivatedafterpowerfailuresor

when the machine is unplugged.

 IfyouswitchoffthemachinebypressingtheOn/Off

buttonwhentheChildLockisactiveandthemachineis

running, then the child lock will be deactivated.

Progress of programme

Progress of a running programme can be followed from the

ProgrammeFollow-upindicator.Atthebeginningofevery

programme step, the relevant indicator light will turn on and

light of the completed step will turn off.

You can change the auxiliary functions, speed and

temperature settings without stopping the programme flow

while the programme is running. To do this, the change

you are going to make must be in a step after the running

programmestep.Ifthechangeisnotcompatible,relevant

lights will flash for 3 times.

 Ifthemachinedoesnotpasstothespinningstep,

RinseHoldfunctionmightbeactiveortheautomatic

unbalanced load detection system might be activated

due to the unbalanced distribution of the laundry in the

machine.

Loading door lock

There is a locking system on the loading door of the machine

that prevents opening of the door in cases when the water

level is unsuitable.

Loadingdoorlightwillstartflashingwhenthemachine

is switched to Pause mode. Machine checks the level of

thewaterinside.Ifthelevelissuitable,LoadingDoorlight

illuminatessteadilywithin1-2minutesandtheloadingdoor

can be opened.

Ifthelevelisunsuitable,LoadingDoorlightturnsoffandthe

loadingdoorcannotbeopened.Ifyouareobligedtoopen

theLoadingDoorwhiletheLoadingDoorlightisoff,you

havetocancelthecurrentprogramme;see"Cancelingthe

programme".

Changing the selections after

programme has started

Switching the machine to pause mode

PresstheStart/Pausebuttontoswitchthemachinetopause

mode while a programme is running. The light of the step

which the machine is in starts flashing in the Programme

Follow-upindicatortoshowthatthemachinehasbeen

switched to the pause mode.

Also,whentheloadingdoorisreadytobeopened,Loading

Doorlightwillalsoilluminatecontinuouslyinadditiontothe

programme step light.

Changing the speed and temperature settings for

auxiliary functions

Dependingonthesteptheprogrammehasreached,you

maycanceloractivatetheauxiliaryfunctions;see,"Auxiliary

function selection".

Youmayalsochangethespeedandtemperaturesettings;

see, "Spin speed selection" and "Temperature selection".

 Ifnochangeisallowed,therelevantlightwillflashfor3

times.

Adding or taking out laundry

PresstheStart/Pausebuttontoswitchthemachineto

pausemode.Theprogrammefollow-uplightoftherelevant

step during which the machine was switched into the pause

modewillflash.WaituntiltheLoadingDoorcanbeopened.

OpentheLoadingDoorandaddortakeoutthelaundry.

ClosetheLoadingDoor.Makechangesinauxiliaryfunctions,

temperatureandspeedsettingsifnecessary.PressStart/

Pause button to start the machine.

The loading door will not open if the water temperature

in the machine is high or the water level is above the

door opening.

Canceling the programme

To cancel the programme, turn the Programme Selection

knob to select another programme. Previous programme will

becanceled.End/Cancellightwillflashcontinuouslytonotify

that the programme has been canceled.

Pumpfunctionisactivatedfor1-2minutesregardlessofthe

programme step, and whether there is water in the machine

or not. After this period, your machine will be ready to start

with the first step of the new programme.

 Dependingonthestepwheretheprogrammewas

canceled in, you may have to put detergent and softener

again for the programme you have selected anew.

 Ifyouwanttoopentheloadingdoorafteryouhave

cancelled the programme but it is not possible to open

the loading door since the water level in the machine

is above the loading door opening, then turn the

Programme Selection knob to Pump+Spin programme

and discharge the water in the machine.

End of programme

“End” appears on the display at the end of the programme.

Wait until the loading door light illuminates steadily. Press On

/Offbuttontoswitchoffthemachine.Takeoutyourlaundry

and close the loading door. Your machine is ready for the next

washing cycle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg WNF 7300 WE20 in the language / languages: English, German, Italian as an attachment in your email.

The manual is 3,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blomberg WNF 7300 WE20 Manual

Product: