581565
5
Zoom out
Zoom in
Previous page
1/44
Next page
5
EN
2 Installation
Refer to the nearest Authorised Service Agent for
installation of your product.
C Preparation of location and electrical installation for
the product is under customer’s responsibility.
BInstallation and electrical connections must be carried
out by a qualified personnel.
A Prior to installation, visually check if the product
has any defects on it. If so, do not have it installed.
Damaged products will cause risks for your safety.
Appropriate installation location
Install the product in an environment which has no
risk of freezing and is in a stable and level position.
Operate your product in a well ventilated, dust-free
environment.
Do not block the air ducts in front of and under the
product with materials such as long pile rugs and
wooden bands.
Do not place your product on a long pile rug or on
similar surfaces.
Do not install the product behind a door with a lock,
sliding door or a hinged door which can strike the
product.
Once the product is installed, it should stay at the
same place where its connections have been made.
When installing the product, make sure that the rear
wall of it does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product at a place
where it will stay permanently.
B Do not place the product on top of the power cable.
Keep at least 1.5 cm distance to walls of other
furniture.
Removing the transportation safety
assembly
ARemove the transportation safety assembly before
using the product for the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum that contains a
piece of styrofoam. Hold it from its section marked
with XX.
3. Pull the nylon towards yourself and remove the
transportation safety assembly.
AMake sure that you have removed the transportation
safety assembly (nylon+styrofoam pieces) before using
the product for the first time. Do not leave any items
inside the drum.
Under counter installation
A special part (Part no. 297 360 0100) replacing
the top trim must be provided and installed by the
Authorised Service Agent in order to use the machine
under a counter or in a cupboard. It should never be
operated without the top trim.
Leave at least 3 cm of space between the side and
rear walls of the product and the walls of the counter/
cupboard when installing your product under a counter
or in a cupboard.
Mounting over a washing machine
A fitting device should be used between the two
machines when installing above a washing machine.
The bracket (Part no. 297 720 0100 white/297 720
0400 grey) must be installed by the Authorised Service
Agent.
Place the product on a firm floor. If it will be placed on
top of a washing machine, the approximate weight of
both machines may reach 180 kg when they are full.
Therefore, the floor must be capable of carrying the
load on it!
Connection to water drain;
In products equipped with a condenser unit the water
accumulated during the drying cycle is collected in the
water tank. You should drain the accumulated water after
each washing cycle.
You can directly send the accumulated water out through
the water drain hose supplied with the machine instead of
periodically draining the water collected in the water tank.
Connecting the water drain hose;
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg TKF 8431 G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg TKF 8431 G in the language / languages: English, German as an attachment in your email.

The manual is 5,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info