582140
5
Zoom out
Zoom in
Previous page
1/68
Next page
5
EN
2 Installation
Refer to the nearest Authorised Service Agent
for installation of your product.
C Preparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections must
be carried out by a qualified personnel.
A Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
Appropriate installation location
Install the product in an environment which
has no risk of freezing and is in a stable and
level position.
Operate your product in a well ventilated,
dust-free environment.
Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
Do not place your product on a long pile rug
or on similar surfaces.
Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
B Do not place the product on top of the
power cable.
Keep at least 1.5 cm distance to walls of
other furniture.
Removing the transportation
safety assembly
ARemove the transportation safety assembly
before using the product for the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum that
contains a piece of styrofoam. Hold it from
its section marked with XX.
3. Pull the nylon towards yourself and remove
the transportation safety assembly.
AMake sure that you have removed
the transportation safety assembly
(nylon+styrofoam pieces) before using the
product for the first time. Do not leave any
items inside the drum.
Under counter installation
A special part (Part no. 297 360 0100)
replacing the top trim must be provided and
installed by the Authorised Service Agent in
order to use the machine under a counter or
in a cupboard. It should never be operated
without the top trim.
Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in a
cupboard.
Mounting over a washing machine
A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no. 297
720 0100 white/297 720 0400 grey) must be
installed by the Authorised Service Agent.
Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the load
on it!
Connection to water drain;
In products equipped with a condenser unit the
water accumulated during the drying cycle is
collected in the water tank. You should drain the
accumulated water after each washing cycle.
You can directly send the accumulated water
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg TKF 8431 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg TKF 8431 A in the language / languages: English, Danish as an attachment in your email.

The manual is 8,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info