302199

Blomberg taf 7330 Manual

38
Zoom out
Zoom in
Previous page
1/44
Next page
15 - EN
C Dryness level of the laundry is
detected by sensors during a drying
cycle and the remaining time is
updated automatically.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program:
1. Press the “Start/Pause/Cancel” button
for about 4 seconds. The “:” in the
middle of the screen will stop flashing.
The “Start/Pause/Cancel” light will
go off and the remaining time on the
screen disappears.
2. Press the "Start/Pause/Cancel" button
to start the program right away.
Starting the Program
1. Press the "Start/Pause/Cancel" button
to start the program.
2. The “Start/Pause/Cancel” button will
light up to indicate that the program
has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step,
the relevant indicator lamp will light up and
light of the completed step will turn off.
"Drying":
- Drying level will be illuminated during
the whole drying process until the drying
degree reaches "iron dry".
"Iron Dry":
- Starts to illuminate when the drying
degree reaches "iron dry" step and remains
illuminated until the next step.
"Cupboard Dry":
- Starts to illuminate when the drying degree
reaches "Cupboard dry" step and remains
illuminated until the next step.
“Cooling”:
- It lights up during the 4-minute cooling
phase at the end of drying.
“Final / Anti-creasing”:
- Illuminates when the program comes
to an end and anti-creasing function is
activated.
Important:
If more than one LED light up or flash
concurrently, it means there is malfunctioning
or a failure (please see, Solution
suggestions for problems).
Changing the program after the
program has started
Youcanusethisfeatureafteryourmachine
has started to dry your clothes under higher
or lower temperatures.
For example;
Press and hold the “Start/Pause/Cancel”
button for about 4 seconds to “Cancel”
the program in order to select “Extra Dry”
program instead of “Iron Ready” program.
Select the “Extra Dry” program by rotating the
program knob.
Press the "Start/Pause/Cancel" button to
start the program.
C The program which is selected first will
go on even if the program selection
button is moved and another program
mode is selected while the machine is
operating.Youmustcanceltheongoing
program in order to change the drying
program. (See, Ending the program
through canceling)
Adding/removing laundry in standby
mode
In order to add or take out laundry after the
start-up of the program;
1. Press the “Start/Pause/Cancel” button
to switch the machine to “Pause” mode.
Drying process will stop.
2. OpenthedooratStoppositionandclose
it again after adding or taking out laundry.
3. Press "Start/Pause/Cancel" button to
start the program.
C Any laundry added after the drying
process was started may cause the
already dried clothes in the machine
intermingle with wet clothes and the
result will be wet laundry after the drying
process is over.
C Laundry may be added or taken out
as much as desired during a drying
process, but as this process will interrupt
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg taf 7330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg taf 7330 in the language / languages: English, German as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blomberg taf 7330

Blomberg taf 7330 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info