626839
18
Zoom out
Zoom in
Previous page
1/156
Next page
16
4.2 STEALTH 875™ & STEALTH 885™
4.2.1 Installation
Stealth Above Counter Installation
Select a location that is near an electrical outlet� Also consider proximity to
ingredients, and patrons as well as available counter space�
Place the blender on the counter in a spot where the air intake vents on the
sides and exhaust on the back of the blender are unobstructed
Ensure there is enough room above and around the unit to allow for unhampered
movement of the sound enclosure (see Figure 1 for measurements)�
Plug the unit into an outlet with appropriate electrical protection�
Stealth In-Counter - Preparation for Installation
Note: You may locate your Blendtec Stealth in the same space as your previous
Blendtec in-counter blender. Just remember to ensure proper spacing for the
sound enclosure (see Figure 1 for measurements).
Identify the desired blender location� Consider proximity to ingredients, and
patrons as well as available counter space� Also ensure that an electrical outlet
is readily accessible�
Ensure the location meets all dimensional requirements (see Figures 1 and 3)�
The countertop can be no thicker than ¾” (1�9 cm)� A thicker countertop will obstruct
motor ventilation�
If installing more than one blender, allow 14”–16” (356 - 40�6 cm) of center-to-center
blender spacing�
If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the
sound enclosure to the wall and 26” (66 cm) from the countertop to any over-the-
counter cabinetry
Ensure lower cabinetry allows adequate airflow�
The blender draws ambient air into the vent holes located on the lower back of
the motor and then evacuates hot air through the vents located on the lower front
and sides of the motor� For the motor to cool properly, a sufcient amount of air
must be able to circulate around the motor�
There should be at least 6 ½” (16�5 cm) of space from the countertop to the
next lower shelf of the cabinet, leaving a minimum space of 3” (76 cm) between
the bottom of the motor and the lower shelf� Cabinetry should not be closed; it
should allow air to flow freely from the outside to the inside of the cabinet space
Plastic bags, cups, and so forth, should not be stored closer than 3” (76 cm) from
the bottom of the motor
Cut a hole in the countertop 4 ⅜“ (111 cm) wide and 5 ⅞” (149 cm) long (see the
countertop hole template in Appendix A)� Ensure that the 4 ⅜” (11�1 cm) sides are
parallel with the machine operator
Note: Double check to ensure that all space requirements and measurements
are correct BEFORE cutting.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blendtec STEALTH 885 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec STEALTH 885 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 5.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blendtec STEALTH 885

Blendtec STEALTH 885 User Manual - English - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info