626838

Blendtec STEALTH 875 Manual

5
Zoom out
Zoom in
Previous page
1/19
Next page
76
• If installing more than one blender, allow 14”–16” (35�6 - 40�6 cm) of center-to-center
blender spacing�
• If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the
sound enclosure to the wall and 26” (66 cm) from the countertop to any over-the-
counter cabinetry�
• Ensure lower cabinetry allows adequate airflow�
• The blender draws ambient air into the vent holes located on the lower back of
the motor and then evacuates hot air through the vents located on the lower front
and sides of the motor� For the motor to cool properly, a sufficient amount of air
must be able to circulate around the motor�
• There should be at least 6 ½” (16�5 cm) of space from the countertop to the
next lower shelf of the cabinet, leaving a minimum space of 3” (7�6 cm) between
the bottom of the motor and the lower shelf� Cabinetry should not be closed; it
should allow air to flow freely from the outside to the inside of the cabinet space�
• Plastic bags, cups, and so forth, should not be stored closer than 3” (7�6 cm) from
the bottom of the motor�
• Cut a hole in the countertop 4 ⅜“ (11�1 cm) wide and 5 ⅞” (14�9 cm) long (see the
countertop hole template in Appendix A)� Ensure that the 4 ⅜” (11�1 cm) sides are
parallel with the machine operator�
Note: Double check to ensure that all space requirements and measurements
are correct BEFORE cutting.
In-Counter Installation
• Feed the electrical cord through the hole in the countertop�
• Gently place the blender unit into the hole�
• Ensure the gasket is seated correctly, lying flat against the counter surface and
not pinched by the housing�
• Plug the unit into an outlet with appropriate electrical protection�
Figure 3. Stealth In-Counter Clearance
3” (7.6 cm)
Minimum
clearance
¾” (1.9 cm)
Maximum
thickness
4.1.2 Stealth 875™ Quick Start Guide
1� Touch the power icon to turn on the blender�
2� Raise the sound enclosure lid�
3� Place the blender jar on the motor base, ensuring the jar is completely seated
and the jar lid is secured�
4� Close the sound enclosure lid�
5� On the control surface, touch the desired blend cycle number, pulse icon or
desired location on the slider control bar�
6� To stop a blend cycle before the programmed time elapses, press the
cancel/exit button� If you have enabled the Blend Cycle Pause feature, press
the previously selected blend cycle button to pause the cycle� To resume
the paused cycle, press the previously selected blend cycle button again�
4.1.3 Stealth 885™ Quick Start Guide
1� Press the power icon to turn on the blender�
2� Raise the sound enclosure lid�
3� Place the blender jar on the motor base, ensuring the jar is completely seated
and the jar lid is secured�
4� Close the sound enclosure lid�
5� On the control surface, press the desired blend cycle number or pulse icon�
6� To stop a blend cycle before the programmed time elapses, press the
cancel/exit button� If you have enabled the Blend Cycle Pause feature, press
the previously selected blend cycle button to pause the cycle� To resume
the paused cycle, press the previously selected blend cycle button again�
4.1.4 Automatic Cycle Operation
Your Stealth blender is preprogrammed with multiple blender profiles to help
operators achieve consistent blends with a minimum of training, trial, and error�
You can select from the following profiles and blend cycles:
Scroll (visible in programming mode)
Power Cancel/Exit
Mode
Slider Control Bar
Preprogrammed Cycle Buttons
Pulse
Select (visible in programming mode)
Scroll
Power
Cancel/Exit
Preprogrammed Cycle Buttons
Pulse
Select
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blendtec STEALTH 875 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec STEALTH 875 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blendtec STEALTH 875

Blendtec STEALTH 875 User Manual - English, French, Spanish - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info